Samsung Galaxy S2 G (i9100g)

Cyanogenmod ROM Samsung Galaxy S2 (i9100)

Cyanogenmod ROM Samsung Galaxy S2 (G) – (i9100g)

Quick Info

Download CyanogenMod

Download (nightly build)
CyanogenMod 11 (Android 4.4-4.4.4 (KitKat))

Notes

The I9100G is NOT to be confused with the the similarly named I9100, which uses an Exynos SoC rather than TI OMAP, and is a very different device. Users running Android 2.3 on their I9100G MUST first upgrade to stock Android 4.x before installing CyanogenMod, or the device won’t boot into the system due to it relying on a newer bootloader. A 4.1 bootloader is recommended.

Special boot modes

  • Recovery: Volume Up, Home, & Power
  • Download: Volume Down, Home & Power

Source code

Device http://www.github.com/cyanogenmod/android_device_samsung_i9100g
Kernel http://www.github.com/cyanogenmod/android_kernel_samsung_t1
Galaxy S II G Specifications
Codename: i9100g
Vendor: Samsung
Manufacturer: samsung
Release date: 2011 August 11
Type: phone
GSM freq: 850 900 1800 1900 MHz GPRS/EDGE
850 900 1900 2100 MHz UMTS/HSPA+
Platform: TI OMAP4430
CPU: 1.2 GHz dual-core Cortex A9
GPU: PowerVR SGX540
RAM: 1GB
Weight: 116 g (4.1 oz)
Dimensions: 125 mm (4.9 in) (h)
66 mm (2.6 in) (w)
9 mm (0.354 in) (d)
Screen size: 109 mm (4.3 in)
Resolution: 800×480
Screen density: 222 PPI
Internal storage: 16/32GB
SD Card: up to 32GB
Bluetooth: 4.0
Wi-Fi: 802.11 a/b/g/n
Main camera: 8MP w/ flash
Secondary camera: 1.9MP
Power: 1650 mAh
CM supported: 9, 10, 10.1, 10.2, 11

How to Install CyanogenMod on the Samsung Galaxy S II G (i9100g)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Important Notes

The I9100G is NOT to be confused with the the similarly named I9100, which uses an Exynos SoC rather than TI OMAP, and is a very different device. Users running Android 2.3 on their I9100G MUST first upgrade to stock Android 4.x before installing CyanogenMod, or the device won’t boot into the system due to it relying on a newer bootloader. A 4.1 bootloader is recommended.

Installing a custom recovery

Samsung devices come with a unique boot mode called Download Mode which is very similar to Fastboot Mode on some devices with unlocked bootloaders. Heimdall is a cross-platform, open source tool for interfacing with Download Mode on Samsung devices. The preferred method of installing a custom recovery is through this boot mode. Rooting the stock firmware is neither recommended nor necessary.

  1. Download and install the Heimdall Suite
    • Windows: Extract the Heimdall suite and take note of the directory holding heimdall.exe. You can verify Heimdall is working by opening a command prompt in this directory and typing heimdall version. If you receive an error, be sure that you have the Microsoft Visual C++ 2012 Redistributable Package (x86/32bit) installed on your computer.
    • Linux: Pick the appropriate installation package based on your distribution. The -frontend packages are not required for this guide. After installation, heimdall should be available from the terminal; type heimdall version to verify installation succeeded.
    • Mac: Install the dmg package. After installation, heimdall should be available from the terminal; type heimdall version to verify installation succeeded.
    • Building from source: The source code for the Heimdall Suite is available on Github. For more details about how to compile the Heimdall Suite, please refer to the README file on Github under the relevant operating system directory. You can also refer to the Install and compile Heimdall instructions on this wiki.
  2. Download recovery — visit TWRP site to check for the latest version of recovery for your device (if your device can be found there). For general info about recoveries click here.
  3. Power off the Galaxy S II G and connect the USB adapter to the computer but not to the Galaxy S II G, yet.
  4. Boot the Galaxy S II G into download mode. Volume Down, Home & Power Accept the disclaimer on the device. Then, insert the USB cable into the device.
  5. Windows (only) driver installation – Skip this step if you are using Linux or Mac
    A more complete set of the following instructions can be found in the Zadig User Guide.
    1. Run zadig.exe from the Drivers folder of the Heimdall Suite.
    2. Choose Options » List All Devices from the menu.
    3. Select Samsung USB Composite Device or MSM8x60 or Gadget Serial or Device Name from the drop down menu. (If nothing relevant appears, try uninstalling any Samsung related Windows software, like Samsung Windows drivers and/or Kies).
    4. Click Replace Driver (having selecting “Install Driver” from the drop down list built into the button).
    5. If you are prompted with a warning that the installer is unable to verify the publisher of the driver, select Install this driver anyway. You may receive two more prompts about security. Select the options that allow you to carry on.
  6. At this point, familiarize yourself with the Flashing with heimdall notes below so that you are prepared for any strange behaviour if it occurs.
  7. On the computer, open a terminal (or Command Prompt on Windows) in the directory where the recovery image is located and type:
    heimdall flash --kernel zImage --no-reboot
    Tip: The file may not be named identically to what’s in this command. If the file is wrapped in a zip or tar file, extract the file first, because heimdall isn’t going to do it for you.
    Note: this device has an initramfs recovery, meaning recovery is actually packaged inside a kernel image. Substitute the filename of the kernel/recovery combo that you downloaded in place of zImage above.
  8. A blue transfer bar will appear on the device showing the recovery being transferred.
  9. Unplug the USB cable from your device.
    • NOTE: Be sure to reboot into recovery immediately after having installed the custom recovery. Otherwise the custom recovery will be overwritten and the device will reboot (appearing as though your custom recovery failed to install).
  10. Manually reboot the phone into recovery mode by performing the following. Volume Up, Home, & Power
  11. The Galaxy S II G now has a custom recovery installed. Continue to the next section.

Note: Flashing with heimdall

  • In Windows 7 UAC (User Account Control) may need switching off. Once Heimdall is finished it can be re-enabled.
  • Protocol initialization can fail if the device is connected via a USB hub – connect the USB cable directly to the PC
  • It may be necessary to run the heimdall flash command as root in Linux or Mac OS X: sudo heimdall flash [...]. Typical symptoms of this are:
    • a blue bar doesn’t show up after the process has finished
    • Failed to confirm end of file transfer sequence!
  • It may be necessary to capitalize the name of the partition on some devices. Try --KERNEL instead of --kernel and/or --recovery instead of --RECOVERY.
  • If on Linux 64bit you get “unable to execute ./heimdall: No such file or directory”, try the 32bit version and make sure to run it with sudo: reference.
  • On Mac OS X you may see this message: “ERROR: Claiming interface failed!”. If so, you need to disable the default USB drivers with the following commands:
    sudo kextunload -b com.apple.driver.AppleUSBCDC;
    sudo kextunload -b com.apple.driver.AppleUSBCDCACMControl;
    sudo kextunload -b com.apple.driver.AppleUSBCDCACMData;
    If you have installed Samsung Kies, you may further need to unload those USB drivers with the following commands:
    sudo kextunload -b com.devguru.driver.SamsungComposite;
    sudo kextunload -b com.devguru.driver.SamsungACMData
    sudo kextunload -b com.devguru.driver.SamsungACMControl
  • Using Heimdall version 1.4.0 (the latest version available for download on the Glass Echidna website) you may see this message or one similar to it:
    Error: Failed to confirm end of PIT file transfer!
    If you experience this error, follow the instructions for compiling Heimdall from source to get the latest version on GitHub with the issue patched.

Helpful Tip

  • The stock ROM may overwrite your custom recovery on boot. To prevent this, boot immediately into recovery after leaving Download Mode instead of letting the ROM boot up normally. If your recovery is overwritten, simply redo the steps you followed above and catch it before it boots next time.
  • Note for upgrades from gingerbread to jellybean remember the recovery is changed. This means once you install do NOT restore to old-gingerbread-stock ROM from cwm-recovery.
  • To upgrade from stock/CM7/CM9/CM10.1.2/CM10.1.3 to CM10.2, you must first boot into recovery and wipe data, cache, and dalvik cache (factory reset). Due to the new partition layout in CM10.2, failing to perform these steps will result in a bootloop. See here for details; more about repartitioning here. If you missed this step before installing, boot to recovery and factory reset, then reinstall CM10.2.
  • Some users have reported connection errors if the device is connected to a USB hub. If you experience such errors it is recommended that you try connecting your device to a USB port on the motherboard.
  • Antivirus software may prevent Heimdall from connecting properly. Disable your antivirus before proceeding.
  • When Heimdall fails to connect, the Download mode may get stuck, making all further attempts fail too. To retry, you may need to restart the Download mode: turn off the phone by holding Power for 5-10 seconds (or by pulling out the battery), then boot into Download mode and run Heimdall again.
  • If Heimdall fails to connect (errors related to initializing the protocol, or transferring data):
    if you just installed the driver, try rebooting your computer and trying again.
    if you still have troubles after reboot, in Zadig try installing the libusbK driver rather than the WinUSB driver.

Installing CyanogenMod from recovery

  1. Make sure your computer has working adb.
  2. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  3. Boot to recovery mode, and connect the phone to your computer through USB.
    • Volume Up, Home, & Power
  4. In ClockworkMod Recovery, use the physical volume buttons to move up and down. On most devices, the power button is used to confirm a menu selection, but for some devices a physical home key acts as a selector. Some devices have touch enabled ClockworkMod Recovery, in which case you may be able to swipe to, or touch, menu selections.
  5. Optional (Recommended): Select backup and restore to create a backup.
  6. Select wipe data/factory reset.
  7. You have two options for transferring and installing the installation packages. The sideload method is more universal across devices, whereas the push and install method is more commonly used:
    • Sideload method: select install zip > install zip from sideload. Follow the on-screen notices to install the package. The installer does not necessarily display an “Install complete.” message. You can tell the install is complete if there were no fatal error messages and you have regained control over the menu.
    • Push and install method: Open a command prompt (or Terminal on Mac and Linux) and navigate to the directory holding the package(s) you would like to install. On the device, navigate to the mounts and storage menu. If you see /storage/sdcard0 or /sdcard as a mountable volume, go ahead and mount it. If you do not see one of these partitions, then instead mount the /data partition. Take note of which volume you mounted. Now, push the package(s) to your device (also, see tip below):
    – If you mounted /storage/sdcard0, then: adb push update.zip /storage/sdcard0/
    – If you mounted /sdcard or /data, then: adb push update.zip /sdcard/
    where update.zip should be replaced with the package filename. Go back to the main menu and select install zip. Choose to install from the same directory where you pushed the package(s). If you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it.
  8. Once installation has finished, return to the main menu and select reboot system now. The device will now boot into CyanogenMod.

Helpful Tip – SD card folders

CyanogenMod 10.1 and newer have multi-user support (introduced in Android 4.2). If your device has storage on the /data partition, then Android actually looks in /data/media/0/ for the first user’s /sdcard/ storage. ClockworkMod recovery symlinks /sdcard/ to /data/media/ though. So, if you are pushing files to internal storage in recovery and want them to be visible in Android, you should push them to /sdcard/0/ or /data/media/0/. Here’s the most frequent scenarios:

  1. If you’re coming from a ROM with Android 4.1 or older to CyanogenMod 10 or older: adb push update.zip /sdcard/
  2. If you’re coming from a ROM with Android 4.1 or older to CyanogenMod 10.1 or newer: adb shell "mkdir /sdcard/0/" followed by adb push update.zip /sdcard/0/
  3. If you’re coming from a ROM with Android 4.2 or newer to CyanogenMod 10.1 or newer: adb push update.zip /sdcard/0/

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For Samsung Galaxy S II G (i9100g)

Introduction

These instructions will hopefully assist you to start with a stock Galaxy S II G, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A Galaxy S II G
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the Galaxy S II G (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b cm-13.0

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast i9100g

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast i9100g

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your Galaxy S II G is connected to your computer via the USB cable and that you are in the ~/android/system/device/samsung/i9100g directory (you can cd ~/android/system/device/samsung/i9100g if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/samsung directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/samsung directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch i9100g

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make i9100g should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/i9100g/cm_i9100g-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-13.0-20161224-UNOFFICIAL-i9100g.zip, which is the CyanogenMod installation package.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-13.0-20161224-UNOFFICIAL-i9100g.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

Oppo N1 (n1)

Cyanogenmod ROM OPPO N1

Cyanogenmod ROM OPPO N1 (n1)

Quick Info

Download CyanogenMod

Download (nightly build)
CyanogenMod 11 (Android 4.4-4.4.4 (KitKat))

Notes

Note: Officially supported by Cyanogen Inc.

The Oppo N1 is officially supported by Cyanogen Inc. More information, including factory images, can be found at cyngn.com/products/n1/

Special boot modes

  • Recovery: With the device powered down, hold the Volume Down and Power buttons.
  • Fastboot: With the device powered down, hold the Volume Up and Power buttons.

Source code

Device http://www.github.com/cyanogenmod/android_device_oppo_n1
Kernel http://www.github.com/cyanogenmod/android_kernel_oppo_n1
N1 Specifications
Codename: n1
Vendor: Oppo
Release date: 2013 December
Type: phone
GSM freq: 850 900 1800 1900 MHz
CDMA freq: 850 900 1700 1900 2100 MHz
Platform: Qualcomm Snapdragon 600
CPU: 1.7 GHz quad-core Krait 300
GPU: Adreno 320
RAM: 2GB
Weight: 213 g
Dimensions: 170.7 mm (h)
82.6 mm (w)
9 mm (d)
Screen size: 150 mm (5.9 in)
Resolution: 1920×1080
Screen density: 377 ppi
Screen type: IPS LCD
Internal storage: 16GB, 32GB
Bluetooth: 4.0
Wi-Fi: 802.11 b/g/n
Main camera: Rotation enabled, 13MP with dedicated ISP, flash: Dual-mode LED
Peripherals: O-Touch, USB OTG, Wi-Fi Direct, Wi-Fi Display, GPS, NFC, Distance sensor, Light sensor, G-sensor, 4D Gyroscope
CM supported: 10.2, 11

How to Install CyanogenMod on the Oppo N1 (n1)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Important Notes

Note: Officially supported by Cyanogen Inc.

The Oppo N1 is officially supported by Cyanogen Inc. More information, including factory images, can be found at cyngn.com/products/n1/

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  2. Download recovery — you can directly download a recovery image using the link below, or visit twrp.me to obtain the latest version of Team Win Recovery Project for your device.
    Recovery: Download
    md5: f771f3d52b05b365146f376bbdc3395b
  3. Connect the N1 to the computer via USB.
  4. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  5. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  6. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  7. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  8. Once the flash completes successfully, reboot the device into recovery to verify the installation. Boot to recovery instructions: With the device powered down, hold the Volume Down and Power buttons.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Installing CyanogenMod from recovery

  1. Make sure your computer has working adb.
  2. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  3. Place the CyanogenMod .zip package, as well as any optional .zip packages, on the root of /sdcard:
    • Using adb: adb push filename.zip /sdcard/
    Note: You can copy the .zip packages to your device using any method you are familiar with. The adb method is used here because it is universal across all devices and works in both Android and recovery mode. If you are in recovery mode, you may need to ensure /sdcard (sometimes called Internal Storage) is mounted by checking its status in the Mounts menu. If you have booted regularly, USB debugging must be enabled.
  4. If you are not already in recovery, boot to recovery mode now.
    • With the device powered down, hold the Volume Down and Power buttons.
  5. In Team Win Recovery Project, select menu choices by tapping on the appropriately labelled button.
  6. Optional (Recommended): Select the Backup button to create a backup.
  7. Select Wipe and then Factory Reset.
  8. Select Install.
  9. Navigate to /sdcard and select the CyanogenMod .zip package.
  10. Follow the on-screen notices to install the package.
  11. Optional: Install any additional packages you wish using the same method (if you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it).
  12. Once installation has finished, return to the main menu and select Reboot, then System. The device will now boot into CyanogenMod.

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For Oppo N1 (n1)

Introduction

These instructions will hopefully assist you to start with a stock N1, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A N1
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the N1 (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b cm-13.0

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast n1

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast n1

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your N1 is connected to your computer via the USB cable and that you are in the ~/android/system/device/oppo/n1 directory (you can cd ~/android/system/device/oppo/n1 if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/oppo directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/oppo directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch n1

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make n1 should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/n1/cm_n1-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-13.0-20161224-UNOFFICIAL-n1.zip, which is the CyanogenMod installation package.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  1. Connect the N1 to the computer via USB.
  2. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  3. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  4. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  5. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  6. Once the flash completes successfully, reboot the device into recovery to verify the installation.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-13.0-20161224-UNOFFICIAL-n1.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

LG Optimus Black (p970)

Cyanogenmod ROM LG Optimus Black (P970)

Cyanogenmod ROM LG Optimus Black (p970)

Quick Info

Download CyanogenMod

Download (nightly build)
CyanogenMod 10.1 (Android 4.2.2 (Jelly Bean))

Special boot modes

  • Recovery: Power & Volume Down

Source code

Device http://www.github.com/cyanogenmod/android_device_lge_p970
Kernel http://www.github.com/cyanogenmod/lge-kernel-sniper
Optimus Black Specifications
Codename: p970
Vendor: LG
Release date: 2011 May
Type: phone
GSM freq: 850 900 1800 1900 MHz GPRS/EDGE

900 1700 1900 2100 MHz UMTS/HSPA

Platform: TI OMAP3630
CPU: 1 GHz single-core Cortex-A8
GPU: PowerVR SGX530
RAM: 512MB
Weight: 109 g (3.8 oz)
Dimensions: 122 mm (4.82 in) (h)
64 mm (2.53 in) (w)
9.2 mm (0.36 in) (d)
Screen size: 102 mm (4.0 in)
Resolution: 480×800
Screen density: 233 PPI
Screen type: IPS LCD
Internal storage: 2 GB (1 GB user available)
SD Card: up to 32GB
Bluetooth: 2.1
Wi-Fi: 802.11 b/g/n
Main camera: 5MP w/ LED flash
Secondary camera: 2MP
Power: 1500 mAh
CM supported: 7, 10, 10.1

Helpful Tip – SD card folders

CyanogenMod 10.1 and newer have multi-user support (introduced in Android 4.2). If your device has storage on the /data partition, then Android actually looks in /data/media/0/ for the first user’s /sdcard/ storage. ClockworkMod recovery symlinks /sdcard/ to /data/media/ though. So, if you are pushing files to internal storage in recovery and want them to be visible in Android, you should push them to /sdcard/0/ or /data/media/0/. Here’s the most frequent scenarios:

  1. If you’re coming from a ROM with Android 4.1 or older to CyanogenMod 10 or older: adb push update.zip /sdcard/
  2. If you’re coming from a ROM with Android 4.1 or older to CyanogenMod 10.1 or newer: adb shell "mkdir /sdcard/0/" followed by adb push update.zip /sdcard/0/
  3. If you’re coming from a ROM with Android 4.2 or newer to CyanogenMod 10.1 or newer: adb push update.zip /sdcard/0/

How To Build CyanogenMod For LG Optimus Black (p970)

Introduction

These instructions will hopefully assist you to start with a stock Optimus Black, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A Optimus Black
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the Optimus Black (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b cm-13.0

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast p970

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast p970

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your Optimus Black is connected to your computer via the USB cable and that you are in the ~/android/system/device/lge/p970 directory (you can cd ~/android/system/device/lge/p970 if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/lge directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/lge directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch p970

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make p970 should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/p970/cm_p970-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-13.0-20161224-UNOFFICIAL-p970.zip, which is the CyanogenMod installation package.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-13.0-20161224-UNOFFICIAL-p970.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

Categories LG

Sony Xperia ZR (dogo)

Cyanogenmod ROM Sony Xperia ZR (Dogo / C5503)

Cyanogenmod ROM Sony Xperia ZR (C5503) (dogo)

Quick Info

Check out Sony Xperia ZR (“dogo”) with newer LineageOS software

LineageOS

Download CyanogenMod

Download (nightly build)
CyanogenMod 13.0 (Android 6.0/6.0.1 (Marshmallow))

Special boot modes

  • Fastboot: With the device powered down, hold Volume Up and connect the USB cable. The notification light should turn blue to indicate you are in fastboot mode.

Source code

Device http://www.github.com/cyanogenmod/android_device_sony_dogo
Kernel http://www.github.com/cyanogenmod/android_kernel_sony_apq8064
Xperia ZR Specifications
Codename: dogo
Also known as: C5503
Vendor: Sony
Release date: 2013 March
Type: phone
GSM freq: 850, 900, 1800, 1900, 2100 MHz UMTS/HSPA+
LTE freq: 800, 850, 1800, 2100, 2600 MHz
Platform: Qualcomm APQ8064, Qualcomm MDM9215M
CPU: 1.5 GHz quad-core Krait Snapdragon S4 Pro
GPU: Adreno 320
RAM: 2GB
Weight: 138 g
Dimensions: 131.3 x 67.3 x 10.5 mm
Screen size: 116 mm (4.6 in)
Resolution: 720×1280
Screen density: 323 ppi
Screen type: TFT
Internal storage: 8GB
SD Card: up to 32GB
Bluetooth: Bluetooth 4.0
Wi-Fi: 802.11a/b/g/n
Main camera: 13 MP
Secondary camera: 2 MP
Power: 2300 mAh
Peripherals: light sensor, proximity sensor, accelerometer, compass, gyroscope
CM supported: 10.1, 10.2, 11, 12.1, 13

How to Install CyanogenMod on the Sony Xperia ZR (dogo)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Unlock your Xperia ZR

What does “unlocking” mean?

The first step in putting any custom operating system on your Xperia ZR is to unlock the bootloader. A bootloader is the very first program that runs when you turn on your device. The bootloader initializes some hardware and then loads the kernel and ramdisk, and gets the boot process going. If the bootloader is in locked mode, it will ensure that only the stock operating system can run. Since you will be installing your own operating system (CyanogenMod), you need to turn this off.

To unlock your bootloader, you’ll first need a program on your computer called adb. One way to get adb is to download and install the Android SDK (Software Developer Kit) from Google. The SDK is used by app developers when they’re writing programs for Android, and who knows, you may want to write apps someday.

Install the Android SDK

Download the SDK, per the steps on Google’s web page. Then install it by following the specific instructions for your computer.

Obtaining the Bootloader Unlock Code

Note:

Unlocking the bootloader on a Sony device may automatically wipe internal storage; a backup of the sdcard is suggested. It will also irreversibly erase the DRM keys stored in the TA partition of some devices, which will result in the loss of certain proprietary features that may have been included. Check your specific device forum on XDA to learn more.

In order to unlock the bootloader on your Xperia ZR you will need to obtain a code from Sony. The following process will help you acquire this code so that you can flash a custom recovery.

  1. Open the Phone application on the Xperia ZR and enter *#06# to obtain the device’s IMEI, IDID or MEID. Save this for later use.
    • Optional: if you do not have a phone app, the IMEI, IDID or MEID can be found on the box or on the device in Settings -> About Device -> Status.
  2. Put the device into fastboot mode:
    • With the device powered down, hold Volume Up and connect the USB cable. The notification light should turn blue to indicate you are in fastboot mode.
  3. Open a terminal on the PC and enter fastboot getvar version
    • If you receive the message <waiting for device> fastboot is not configured properly, please see fastboot for more details.
  4. Navigate a browser here
    • Select your device and click the ‘continue’ button at the bottom of the page.
    • Enter your email address, agree to the terms and select ‘Submit’
    • Click the link from your email, enter your IMEI, IDID or MEID and continue
    • The unlock code should now appear, write this down for the next step.
  5. In the PC’s terminal, enter the following command: fastboot oem unlock 0xKEY
    • KEY corresponds to the unlock code you were given.

The Xperia ZR’s bootloader should now be unlocked.

Installing CyanogenMod on Sony Devices

  1. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  2. Extract boot.img from the zip to your computer, you will need this file for fastboot.
  3. Put the phone into fastboot mode:
    With the device powered down, hold Volume Up and connect the USB cable. The notification light should turn blue to indicate you are in fastboot mode.
  4. Open a terminal on the PC with admin rights, access your platform-tools directory of the Android SDK, and enter the following:
    • fastboot flash boot boot.img
    • fastboot reboot
    While the device reboots, press the Volume rockers a few times to load recovery.
Note: Make the selection below based on the recovery version you see on your screen. If you’re installing CyanogenMod 11, you will have CWM Recovery. If installing CyanogenMod 12.0 or newer, you will have CyanogenMod Recovery.
Click here to continue instructions using CyanogenMod Recovery
Note: Once the device boots into CyanogenMod Recovery, use the physical volume buttons to move up and down. The home button is used to confirm your selection. The recovery is also touch screen friendly, so you can swipe up or down to scroll and tap the item you wish to select.
  1. Optional (Recommended): Using adb you can create a backup on your PC of your apps and app data. Boot the device into android and open a command prompt (or terminal on Mac and Linux) and enter the following:
    • adb backup -apk -all -f backup20161224.ab
    When the backup is complete return to recovery mode.
  2. On the device, select wipe data/factory reset.
  3. You have two options for installing the installation zip packages. (Note: The sideload method requires a recent version of adb to be working in recovery (adb bundled with ubuntu may have protocol errors):
    • Sideload method: Select apply update > apply update from adb. Open a command prompt (or Terminal on Mac and Linux) and enter adb sideload update.zip, where update.zip should be replaced with the package filename. If you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it. The installer does not necessarily display an “Install complete.” message. You can tell the install is complete if there were no fatal error messages and you have regained control over the menu.
    • Install update method: If you previously placed the installation zip packages on your internal storage, select apply update > choose from internal storage. Navigate to the directory where you placed the packages and select one. If you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it.
  4. Once installation has finished, return to the main menu and select reboot system now. The device will now boot into CyanogenMod.

Note:

On all 2011 model Sony devices, the kernel will not update when flashed in recovery, so the kernel must be updated via fastboot every time you flash a new build of CyanogenMod.

Click here to continue instructions using CWM Recovery
Note:Once the device boots into ClockworkMod Recovery, use the physical volume buttons to move up and down. The home button is used to confirm your selection.
  1. Optional (Recommended): Select backup and restore to create a backup of your current ROM.
  2. Select wipe data/factory reset. If you get an error formatting /data, try format /data and /data/media from the mounts and storage menu
  3. You have two options for transferring and installing the installation zip packages. Both cases require a recent version of adb to be working in recovery (adb bundled with ubuntu may have protocol errors). The sideload method is more universal across devices, whereas the push and install method is more commonly used:
    • Sideload method: select install zip > install zip from sideload. Follow the on-screen notices to install the package. The installer does not necessarily display an “Install complete.” message. You can tell the install is complete if there were no fatal error messages and you have regained control over the menu.
    • Push and install method: Open a command prompt (or Terminal on Mac and Linux) and navigate to the directory holding the package(s) you would like to install. On the device, navigate to the mounts and storage menu. If you see /storage/sdcard0 as a mountable volume, go ahead and mount it. If you do not see this directory, then instead mount the /data directory. Take note of which volume you mounted. Now, push the package(s) to your device:
    – If you mounted /storage/sdcard0, then: adb push update.zip /storage/sdcard0/
    – If you mounted /data, then: adb push update.zip /sdcard/0/
    where update.zip should be replaced with the package filename. Go back to the main menu and select install zip. Choose to install from the same directory where you pushed the package(s). If you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it.
  4. Once installation has finished, return to the main menu and select reboot system now. The device will now boot into CyanogenMod.

Note:

On all 2011 model Sony devices, the kernel will not update when flashed in recovery, so the kernel must be updated via fastboot every time you flash a new build of CyanogenMod.

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For Sony Xperia ZR (dogo)

Introduction

These instructions will hopefully assist you to start with a stock Xperia ZR, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A Xperia ZR
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the Xperia ZR (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b cm-13.0

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast dogo

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast dogo

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your Xperia ZR is connected to your computer via the USB cable and that you are in the ~/android/system/device/sony/dogo directory (you can cd ~/android/system/device/sony/dogo if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/sony directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/sony directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch dogo

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make dogo should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/dogo/cm_dogo-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-13.0-20161224-UNOFFICIAL-dogo.zip, which is the CyanogenMod installation package.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-13.0-20161224-UNOFFICIAL-dogo.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

Sony Xperia Z1 (honami)

Cyanogenmod ROM Sony Xperia Z1 (honami, C6902, C6903, C6906, C6943)

Cyanogenmod ROM Sony Xperia Z1 (C6902, C6903, C6906, C6943) (honami)

Quick Info

Download CyanogenMod

Download (nightly build)
CyanogenMod 12.1 (Android 5.1 (Lollipop))

Special boot modes

  • Recovery: Press Volume Up when the notification light is purple.
  • Bootloader: With the device powered down, hold Volume Down and connect the USB cable. The notification light should briefly turn green to indicate you are in flash mode.
  • Fastboot: With the device powered down, hold Volume Up and connect the USB cable. The notification light should turn blue to indicate you are in fastboot mode.

Source code

Device http://www.github.com/cyanogenmod/android_device_sony_honami
Kernel http://www.github.com/cyanogenmod/android_kernel_sony_msm8974
Xperia Z1 Specifications
Codename: honami
Also known as: C6902, C6903, C6906, C6943
Vendor: Sony
Manufacturer: Sony
Release date: 2013 September 15
Type: phone
GSM freq: C6902/C6903/C6906/C6943: UMTS HSPA+: 850 (Band V), 900 (Band VIII), 1700 (Band IV), 1900 (Band II), 2100 (Band I) MHz; GSM GPRS/EDGE 850, 900, 1800, 1900 MHz
LTE freq: C6906: Bands 1, 2, 4, 5, 7, 8, 17; C6903/C6943: Bands 1, 2, 3, 4, 5, 7, 8, 20
Platform: Qualcomm MSM8974
CPU: 2.2 GHz quad-core Krait Snapdragon 800
GPU: Adreno 330
RAM: 2GB
Weight: 170 g
Dimensions: 144 mm (h) x 74 mm (w) x 8.5 mm (d)
Screen size: 127 mm (5.0 in)
Resolution: 1080×1920
Screen density: 441 ppi
Screen type: TFT LCD
Internal storage: 16GB
SD Card: microSD up to 64GB
Bluetooth: Bluetooth 4.0
Wi-Fi: 802.11a/b/g/n/ac
Main camera: 20.7 MP w/ LED flash
Secondary camera: 2.2 MP
Power: 3050 mAh
Peripherals: light sensor, proximity sensor, accelerometer, compass, gyroscope
CM supported: 10.2, 11, 12, 12.1

How to Install CyanogenMod on the Sony Xperia Z1 (honami)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Unlock your Xperia Z1

What does “unlocking” mean?

The first step in putting any custom operating system on your Xperia Z1 is to unlock the bootloader. A bootloader is the very first program that runs when you turn on your device. The bootloader initializes some hardware and then loads the kernel and ramdisk, and gets the boot process going. If the bootloader is in locked mode, it will ensure that only the stock operating system can run. Since you will be installing your own operating system (CyanogenMod), you need to turn this off.

To unlock your bootloader, you’ll first need a program on your computer called adb. One way to get adb is to download and install the Android SDK (Software Developer Kit) from Google. The SDK is used by app developers when they’re writing programs for Android, and who knows, you may want to write apps someday.

Install the Android SDK

Download the SDK, per the steps on Google’s web page. Then install it by following the specific instructions for your computer.

Obtaining the Bootloader Unlock Code

Note:

Unlocking the bootloader on a Sony device may automatically wipe internal storage; a backup of the sdcard is suggested. It will also irreversibly erase the DRM keys stored in the TA partition of some devices, which will result in the loss of certain proprietary features that may have been included. Check your specific device forum on XDA to learn more.

In order to unlock the bootloader on your Xperia Z1 you will need to obtain a code from Sony. The following process will help you acquire this code so that you can flash a custom recovery.

  1. Open the Phone application on the Xperia Z1 and enter *#06# to obtain the device’s IMEI, IDID or MEID. Save this for later use.
    • Optional: if you do not have a phone app, the IMEI, IDID or MEID can be found on the box or on the device in Settings -> About Device -> Status.
  2. Put the device into fastboot mode:
    • With the device powered down, hold Volume Up and connect the USB cable. The notification light should turn blue to indicate you are in fastboot mode.
  3. Open a terminal on the PC and enter fastboot getvar version
    • If you receive the message <waiting for device> fastboot is not configured properly, please see fastboot for more details.
  4. Navigate a browser here
    • Select your device and click the ‘continue’ button at the bottom of the page.
    • Enter your email address, agree to the terms and select ‘Submit’
    • Click the link from your email, enter your IMEI, IDID or MEID and continue
    • The unlock code should now appear, write this down for the next step.
  5. In the PC’s terminal, enter the following command: fastboot oem unlock 0xKEY
    • KEY corresponds to the unlock code you were given.

The Xperia Z1’s bootloader should now be unlocked.

Installing CyanogenMod on Sony Devices

  1. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  2. Extract boot.img from the zip to your computer, you will need this file for fastboot.
  3. Put the phone into fastboot mode:
    With the device powered down, hold Volume Up and connect the USB cable. The notification light should turn blue to indicate you are in fastboot mode.
  4. Open a terminal on the PC with admin rights, access your platform-tools directory of the Android SDK, and enter the following:
    • fastboot flash boot boot.img
    • fastboot reboot
    While the device reboots, press the Volume rockers a few times to load recovery.
Note: Make the selection below based on the recovery version you see on your screen. If you’re installing CyanogenMod 11, you will have CWM Recovery. If installing CyanogenMod 12.0 or newer, you will have CyanogenMod Recovery.
Click here to continue instructions using CyanogenMod Recovery
Note: Once the device boots into CyanogenMod Recovery, use the physical volume buttons to move up and down. The home button is used to confirm your selection. The recovery is also touch screen friendly, so you can swipe up or down to scroll and tap the item you wish to select.
  1. Optional (Recommended): Using adb you can create a backup on your PC of your apps and app data. Boot the device into android and open a command prompt (or terminal on Mac and Linux) and enter the following:
    • adb backup -apk -all -f backup20161224.ab
    When the backup is complete return to recovery mode.
  2. On the device, select wipe data/factory reset.
  3. You have two options for installing the installation zip packages. (Note: The sideload method requires a recent version of adb to be working in recovery (adb bundled with ubuntu may have protocol errors):
    • Sideload method: Select apply update > apply update from adb. Open a command prompt (or Terminal on Mac and Linux) and enter adb sideload update.zip, where update.zip should be replaced with the package filename. If you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it. The installer does not necessarily display an “Install complete.” message. You can tell the install is complete if there were no fatal error messages and you have regained control over the menu.
    • Install update method: If you previously placed the installation zip packages on your internal storage, select apply update > choose from internal storage. Navigate to the directory where you placed the packages and select one. If you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it.
  4. Once installation has finished, return to the main menu and select reboot system now. The device will now boot into CyanogenMod.

Note:

On all 2011 model Sony devices, the kernel will not update when flashed in recovery, so the kernel must be updated via fastboot every time you flash a new build of CyanogenMod.

Click here to continue instructions using CWM Recovery
Note:Once the device boots into ClockworkMod Recovery, use the physical volume buttons to move up and down. The home button is used to confirm your selection.
  1. Optional (Recommended): Select backup and restore to create a backup of your current ROM.
  2. Select wipe data/factory reset. If you get an error formatting /data, try format /data and /data/media from the mounts and storage menu
  3. You have two options for transferring and installing the installation zip packages. Both cases require a recent version of adb to be working in recovery (adb bundled with ubuntu may have protocol errors). The sideload method is more universal across devices, whereas the push and install method is more commonly used:
    • Sideload method: select install zip > install zip from sideload. Follow the on-screen notices to install the package. The installer does not necessarily display an “Install complete.” message. You can tell the install is complete if there were no fatal error messages and you have regained control over the menu.
    • Push and install method: Open a command prompt (or Terminal on Mac and Linux) and navigate to the directory holding the package(s) you would like to install. On the device, navigate to the mounts and storage menu. If you see /storage/sdcard0 as a mountable volume, go ahead and mount it. If you do not see this directory, then instead mount the /data directory. Take note of which volume you mounted. Now, push the package(s) to your device:
    – If you mounted /storage/sdcard0, then: adb push update.zip /storage/sdcard0/
    – If you mounted /data, then: adb push update.zip /sdcard/0/
    where update.zip should be replaced with the package filename. Go back to the main menu and select install zip. Choose to install from the same directory where you pushed the package(s). If you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it.
  4. Once installation has finished, return to the main menu and select reboot system now. The device will now boot into CyanogenMod.

Note:

On all 2011 model Sony devices, the kernel will not update when flashed in recovery, so the kernel must be updated via fastboot every time you flash a new build of CyanogenMod.

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For Sony Xperia Z1 (honami)

Introduction

These instructions will hopefully assist you to start with a stock Xperia Z1, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A Xperia Z1
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the Xperia Z1 (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b cm-13.0

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast honami

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast honami

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your Xperia Z1 is connected to your computer via the USB cable and that you are in the ~/android/system/device/sony/honami directory (you can cd ~/android/system/device/sony/honami if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/sony directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/sony directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch honami

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make honami should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/honami/cm_honami-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-13.0-20161224-UNOFFICIAL-honami.zip, which is the CyanogenMod installation package.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-13.0-20161224-UNOFFICIAL-honami.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

Sony Xperia Z Ultra (togari)

Cyanogenmod ROM Sony Xperia Z Ultra (C6833) (togari)

Cyanogenmod ROM Sony Xperia Z Ultra (C6833) (togari)

Quick Info

Download CyanogenMod

Download (nightly build)
CyanogenMod 12.1 (Android 5.1 (Lollipop))

Special boot modes

  • Fastboot: With the device powered down, hold Volume Up and connect the USB cable. The notification light should turn blue to indicate you are in fastboot mode.

Source code

Device http://www.github.com/cyanogenmod/android_device_sony_togari
Kernel http://www.github.com/cyanogenmod/android_kernel_sony_msm8974
Xperia Z Ultra Specifications
Codename: togari
Also known as: C6833
Vendor: Sony
Manufacturer: Sony
Release date: 2013 June
Type: phone
GSM freq: 850, 900, 1800, 1900 MHz GSM/EDGE/GPRS; 850, 900, 1700, 1900, 2100 MHz UMTS/HSPA+
LTE freq: 700, 850, 900, 1700, 1900, 2100, 2600 MHz
Platform: Qualcomm MSM8974
CPU: 2.2 GHz quad-core Krait Snapdragon S800
GPU: Adreno 330
RAM: 2GB
Weight: 212 g
Dimensions: 179 mm (7.05 in) (h)
92 mm (3.62 in) (w)
6.5 mm (0.26 in) (d)
Screen size: 162 mm (6.4 in)
Resolution: 1080×1920
Screen density: 344 ppi
Screen type: TFT
Internal storage: 16GB
SD Card: up to 64GB
Bluetooth: Bluetooth 4.0
Wi-Fi: 802.11a/b/g/n
Main camera: 8 MP, flash: LED
Secondary camera: 2 MP
Power: 3050 mAh
Peripherals: light sensor, proximity sensor, accelerometer, compass, gyroscope
CM supported: 10.2, 11, 12, 12.1

How to Install CyanogenMod on the Sony Xperia Z Ultra (togari)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Unlock your Xperia Z Ultra

What does “unlocking” mean?

The first step in putting any custom operating system on your Xperia Z Ultra is to unlock the bootloader. A bootloader is the very first program that runs when you turn on your device. The bootloader initializes some hardware and then loads the kernel and ramdisk, and gets the boot process going. If the bootloader is in locked mode, it will ensure that only the stock operating system can run. Since you will be installing your own operating system (CyanogenMod), you need to turn this off.

To unlock your bootloader, you’ll first need a program on your computer called adb. One way to get adb is to download and install the Android SDK (Software Developer Kit) from Google. The SDK is used by app developers when they’re writing programs for Android, and who knows, you may want to write apps someday.

Install the Android SDK

Download the SDK, per the steps on Google’s web page. Then install it by following the specific instructions for your computer.

Obtaining the Bootloader Unlock Code

Note:

Unlocking the bootloader on a Sony device may automatically wipe internal storage; a backup of the sdcard is suggested. It will also irreversibly erase the DRM keys stored in the TA partition of some devices, which will result in the loss of certain proprietary features that may have been included. Check your specific device forum on XDA to learn more.

In order to unlock the bootloader on your Xperia Z Ultra you will need to obtain a code from Sony. The following process will help you acquire this code so that you can flash a custom recovery.

  1. Open the Phone application on the Xperia Z Ultra and enter *#06# to obtain the device’s IMEI, IDID or MEID. Save this for later use.
    • Optional: if you do not have a phone app, the IMEI, IDID or MEID can be found on the box or on the device in Settings -> About Device -> Status.
  2. Put the device into fastboot mode:
    • With the device powered down, hold Volume Up and connect the USB cable. The notification light should turn blue to indicate you are in fastboot mode.
  3. Open a terminal on the PC and enter fastboot getvar version
    • If you receive the message <waiting for device> fastboot is not configured properly, please see fastboot for more details.
  4. Navigate a browser here
    • Select your device and click the ‘continue’ button at the bottom of the page.
    • Enter your email address, agree to the terms and select ‘Submit’
    • Click the link from your email, enter your IMEI, IDID or MEID and continue
    • The unlock code should now appear, write this down for the next step.
  5. In the PC’s terminal, enter the following command: fastboot oem unlock 0xKEY
    • KEY corresponds to the unlock code you were given.

The Xperia Z Ultra’s bootloader should now be unlocked.

Installing CyanogenMod on Sony Devices

  1. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  2. Extract boot.img from the zip to your computer, you will need this file for fastboot.
  3. Put the phone into fastboot mode:
    With the device powered down, hold Volume Up and connect the USB cable. The notification light should turn blue to indicate you are in fastboot mode.
  4. Open a terminal on the PC with admin rights, access your platform-tools directory of the Android SDK, and enter the following:
    • fastboot flash boot boot.img
    • fastboot reboot
    While the device reboots, press the Volume rockers a few times to load recovery.
Note: Make the selection below based on the recovery version you see on your screen. If you’re installing CyanogenMod 11, you will have CWM Recovery. If installing CyanogenMod 12.0 or newer, you will have CyanogenMod Recovery.
Click here to continue instructions using CyanogenMod Recovery
Note: Once the device boots into CyanogenMod Recovery, use the physical volume buttons to move up and down. The home button is used to confirm your selection. The recovery is also touch screen friendly, so you can swipe up or down to scroll and tap the item you wish to select.
  1. Optional (Recommended): Using adb you can create a backup on your PC of your apps and app data. Boot the device into android and open a command prompt (or terminal on Mac and Linux) and enter the following:
    • adb backup -apk -all -f backup20161224.ab
    When the backup is complete return to recovery mode.
  2. On the device, select wipe data/factory reset.
  3. You have two options for installing the installation zip packages. (Note: The sideload method requires a recent version of adb to be working in recovery (adb bundled with ubuntu may have protocol errors):
    • Sideload method: Select apply update > apply update from adb. Open a command prompt (or Terminal on Mac and Linux) and enter adb sideload update.zip, where update.zip should be replaced with the package filename. If you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it. The installer does not necessarily display an “Install complete.” message. You can tell the install is complete if there were no fatal error messages and you have regained control over the menu.
    • Install update method: If you previously placed the installation zip packages on your internal storage, select apply update > choose from internal storage. Navigate to the directory where you placed the packages and select one. If you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it.
  4. Once installation has finished, return to the main menu and select reboot system now. The device will now boot into CyanogenMod.

Note:

On all 2011 model Sony devices, the kernel will not update when flashed in recovery, so the kernel must be updated via fastboot every time you flash a new build of CyanogenMod.

Click here to continue instructions using CWM Recovery
Note:Once the device boots into ClockworkMod Recovery, use the physical volume buttons to move up and down. The home button is used to confirm your selection.
  1. Optional (Recommended): Select backup and restore to create a backup of your current ROM.
  2. Select wipe data/factory reset. If you get an error formatting /data, try format /data and /data/media from the mounts and storage menu
  3. You have two options for transferring and installing the installation zip packages. Both cases require a recent version of adb to be working in recovery (adb bundled with ubuntu may have protocol errors). The sideload method is more universal across devices, whereas the push and install method is more commonly used:
    • Sideload method: select install zip > install zip from sideload. Follow the on-screen notices to install the package. The installer does not necessarily display an “Install complete.” message. You can tell the install is complete if there were no fatal error messages and you have regained control over the menu.
    • Push and install method: Open a command prompt (or Terminal on Mac and Linux) and navigate to the directory holding the package(s) you would like to install. On the device, navigate to the mounts and storage menu. If you see /storage/sdcard0 as a mountable volume, go ahead and mount it. If you do not see this directory, then instead mount the /data directory. Take note of which volume you mounted. Now, push the package(s) to your device:
    – If you mounted /storage/sdcard0, then: adb push update.zip /storage/sdcard0/
    – If you mounted /data, then: adb push update.zip /sdcard/0/
    where update.zip should be replaced with the package filename. Go back to the main menu and select install zip. Choose to install from the same directory where you pushed the package(s). If you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it.
  4. Once installation has finished, return to the main menu and select reboot system now. The device will now boot into CyanogenMod.

Note:

On all 2011 model Sony devices, the kernel will not update when flashed in recovery, so the kernel must be updated via fastboot every time you flash a new build of CyanogenMod.

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For Sony Xperia Z Ultra (togari)

Introduction

These instructions will hopefully assist you to start with a stock Xperia Z Ultra, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A Xperia Z Ultra
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the Xperia Z Ultra (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b cm-13.0

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast togari

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast togari

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your Xperia Z Ultra is connected to your computer via the USB cable and that you are in the ~/android/system/device/sony/togari directory (you can cd ~/android/system/device/sony/togari if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/sony directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/sony directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch togari

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make togari should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/togari/cm_togari-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-13.0-20161224-UNOFFICIAL-togari.zip, which is the CyanogenMod installation package.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-13.0-20161224-UNOFFICIAL-togari.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

Motorola Moto G 2013 (falcon)

Cyanogenmod ROM Motorola Moto G 2013 (falcon, falcon_umts, falcon_gpe, falcon_cdma)

Cyanogenmod ROM Motorola Moto G 2013 (falcon, falcon_umts, falcon_gpe, falcon_cdma)

Quick Info

Check out Motorola Moto G (“falcon”) with newer LineageOS software

LineageOS

Download CyanogenMod

Download (nightly build)
CyanogenMod 14.1 (Android 7.1 (Nougat))

Notes

This is a unified build that supports retail (XT1031, XT1032, XT1033 and XT1034) and Google Play Edition (XT1032).

Special boot modes

  • Recovery: Hold Volume Down & Power simultaneously. On the next screen use Volume Down to scroll to recovery and then use Volume Up to select.
  • Bootloader: Hold Volume Down & Power simultaneously. On the next screen use Volume Down to scroll and Volume Up to select.
  • Fastboot: Hold Volume Down & Power simultaneously.

Source code

Device http://www.github.com/cyanogenmod/android_device_motorola_falcon
Kernel http://www.github.com/cyanogenmod/android_kernel_motorola_msm8226
Moto G Specifications
Codename: falcon
Also known as: falcon_umts, falcon_gpe, falcon_cdma
Vendor: Motorola
Release date: 2013 November
Carrier: AT&T,TMobile,Boost, International GSM
Type: phone
GSM freq: GSM 850/900/1800/1900 MHz, HSDPA 850/900/1900/2100 MHz – International, HSDPA 850/1700/1900/2100 MHz- T-Mobile, AT&T
CDMA freq: CDMA 800/1900 MHz, CDMA2000 1xEV-DO
Platform: Qualcomm Snapdragon 400
CPU: 1.2 GHz quad-core Cortex A7
GPU: Adreno 305
RAM: 1GB
Weight: 143 g (5.04 oz)
Dimensions: 129.9 mm (5.11 in) x 65.9 mm (2.59 in) x 11.6 mm (0.46 in)
Screen size: 114 mm (4.5 in)
Resolution: 720 x 1280 pixels
Screen density: ~326 ppi
Screen type: IPS LCD capacitive touchscreen, 16M colors
Internal storage: 8GB or 16GB
SD Card: none
Bluetooth: v4.0 with A2DP, LE
Wi-Fi: Wi-Fi 802.11 b/g/n, Wi-Fi hotspot
Main camera: 5MP, flash: LED
Secondary camera: 1.3MP
Power: 2070 mAh
Peripherals: Accelerometer, proximity, compass
CM supported: 11, 12, 12.1, 13, 14.1

How to Install CyanogenMod on the Motorola Moto G (falcon)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Important Notes

This is a unified build that supports retail (XT1031, XT1032, XT1033 and XT1034) and Google Play Edition (XT1032).

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to obtain your bootloader unlock code:
    fastboot oem get_unlock_data
  8. Visit the Motorola Bootloader Unlock website and follow the instructions there to obtain your unlock key and unlock your bootloader.
  9. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked.
  10. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  2. Download recovery — you can directly download a recovery image using the link below, or visit twrp.me to obtain the latest version of Team Win Recovery Project for your device.
    Recovery: Download
    md5: 2c91ae6b8b4559b448526d659e57ae20
  3. Connect the Moto G to the computer via USB.
  4. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  5. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  6. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  7. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  8. Once the flash completes successfully, reboot the device into recovery to verify the installation. Boot to recovery instructions: Hold Volume Down & Power simultaneously. On the next screen use Volume Down to scroll to recovery and then use Volume Up to select.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Installing CyanogenMod from recovery

  1. Make sure your computer has working adb.
  2. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  3. Place the CyanogenMod .zip package, as well as any optional .zip packages, on the root of /sdcard:
    • Using adb: adb push filename.zip /sdcard/
    Note: You can copy the .zip packages to your device using any method you are familiar with. The adb method is used here because it is universal across all devices and works in both Android and recovery mode. If you are in recovery mode, you may need to ensure /sdcard (sometimes called Internal Storage) is mounted by checking its status in the Mounts menu. If you have booted regularly, USB debugging must be enabled.
  4. If you are not already in recovery, boot to recovery mode now.
    • Hold Volume Down & Power simultaneously. On the next screen use Volume Down to scroll to recovery and then use Volume Up to select.
  5. In Team Win Recovery Project, select menu choices by tapping on the appropriately labelled button.
  6. Optional (Recommended): Select the Backup button to create a backup.
  7. Select Wipe and then Factory Reset.
  8. Select Install.
  9. Navigate to /sdcard and select the CyanogenMod .zip package.
  10. Follow the on-screen notices to install the package.
  11. Optional: Install any additional packages you wish using the same method (if you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it).
  12. Once installation has finished, return to the main menu and select Reboot, then System. The device will now boot into CyanogenMod.

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For Motorola Moto G (falcon)

Introduction

These instructions will hopefully assist you to start with a stock Moto G, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A Moto G
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the Moto G (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Unlocking your Moto G

What does “unlocking” mean?

Note:

If you’ve already installed CyanogenMod or another ROM on your Moto G, your device is already unlocked. Assuming you also have adb and fastboot installed on your computer, you can skip this whole section and proceed to the HOW TO BUILD section below.

The first step in putting any custom operating system on your Moto G is to unlock the bootloader. A bootloader is the very first program that runs when you turn on your device. The bootloader initializes some hardware and then loads the kernel and ramdisk, and gets the boot process going. If the bootloader is in locked mode, it will ensure that only the stock operating system can run. Since you will be installing your own operating system, you need to turn this off. Luckily, Google and motorola make it easy.

Note: A Warning About Unlocking

THE PROCESS OF UNLOCKING THE BOOTLOADER WILL ERASE ALL YOUR PERSONAL DATA FROM THE DEVICE.

Okay. I’m in. What do I need to do this?

To unlock your bootloader, you’ll first need a program on your computer called fastboot. One way to get fastboot is to download and install the Android SDK (Software Developer Kit) from Google. The SDK is used by app developers when they’re writing programs for Android, and who knows, you may want to write apps someday. But the SDK also contains two great tools that are useful even to non-developers. They are:

  • adb – Android Debug Bridge – this is a program that lets your computer “talk” to your Moto G while the device is running. Among the many things you can do with adb– you can push files from your computer to the device or pull files from the device to your computer, you can get a running real-time log of Android activity (which is very useful for debugging or having others help you debug), you can create an interactive “shell” session (similar to Linux or OS X) to type commands to your device, and much more.

  • fastboot – fastboot works a little bit like adb, except it’s often used at a much earlier point in the boot process, even before Android or any operating system loads. You can put your Moto G into a “fastboot” mode, whereby, if you are connected via USB cable, you can copy entire partitions from your computer (usually in the form of an image file, such as boot.img or recovery.img) over to the device, wiping over whatever happened to be there. Fastboot is able to do more than that, however. It’s also used to send special commands to the device to do things such as unlock your bootloader.

How do I do the actual unlocking?

So this should be a one time thing…

Install the Android SDK

To unlock your Moto G, you will need fastboot installed. Go ahead and download the SDK, per the steps on Google’s web page. Then install it by following the specific instructions for your computer.

Note:

Google’s instructions may be out of date for 12.04. The Sun JDK isn’t available anymore as a dpkg AND they say Eclipse 3.6 isn’t available as a package. Well, 3.7.X is now available. Doing a “$ sudo apt-get install eclipse” will now install the proper Eclipse and JDK (OpenJDK 6).

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to unlock the bootloader:
    fastboot oem get_unlock_data
  8. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked.
  9. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Troubleshooting

If you have issues with fastboot or adb not being found, make sure that the Android SDK folder /platform-tools, which contains the adb and fastboot files, are in the path of execution for commands typed at the terminal. Usually typing something like 

# PATH=$PATH:/your/specific/path/to/android/sdk/platform-tools/

will work for that terminal session.

Note:

The above command requires a bash-like shell. If you’re running a linux distribution which uses a shell such as csh or tcsh, first run /bin/bash to start a bash shell. See http://www.cyberciti.biz/tips/how-do-i-find-out-what-shell-im-using.html or google for more help on that. You will need bash later as well, when using the “. build/envsetup.sh” command.

Note: Linux Mint users

If you have problems with adb (“file not found”) and you’re using 64-bit linux (I don’t know much about Mint, so maybe it’s all 64-bit?) try doing this to see if adb works better: 

$ sudo apt-get install ia32-libs

You’ll be using fastboot again to install a custom recovery.

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b cm-13.0

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast falcon

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast falcon

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your Moto G is connected to your computer via the USB cable and that you are in the ~/android/system/device/motorola/falcon directory (you can cd ~/android/system/device/motorola/falcon if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/motorola directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/motorola directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch falcon

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make falcon should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/falcon/cm_falcon-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-13.0-20161224-UNOFFICIAL-falcon.zip, which is the CyanogenMod installation package.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  1. Connect the Moto G to the computer via USB.
  2. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  3. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  4. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  5. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  6. Once the flash completes successfully, reboot the device into recovery to verify the installation.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-13.0-20161224-UNOFFICIAL-falcon.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

Google Nexus S (crespo)

Cyanogenmod ROM Google Nexus S (crespo)

Cyanogenmod ROM Google Nexus S (crespo)

Quick Info

Download CyanogenMod

Download (nightly build)
CyanogenMod 11 (Android 4.4-4.4.4 (KitKat))

Notes

The Nexus S (crespo) is a touchscreen smartphone manufactured by Samsung with direct support from Google. It introduced wireless payment using NFC and Google wallet. It is the second Nexus device.

WARNING:

The newest CM11 Gapps package (20140606) is too big for the /system partition of crespo. Please use the 20140105 package instead.

Special boot modes

  • Recovery: Volume Up & Power

Source code

Device http://www.github.com/cyanogenmod/android_device_samsung_crespo
Kernel http://www.github.com/cyanogenmod/android_kernel_samsung_crespo
Nexus S Specifications
Codename: crespo
Vendor: Google
Manufacturer: Samsung
Release date: 2010 December 16
Type: phone
GSM freq: 850 900 1800 1900 MHz GSM/GPRS/EDGE
900 1700 2100 MHz UMTS/HSPA+ (USA)
850 1900 2100 MHz UMTS/HSPA+ (INTERNATIONAL)
Platform: Samsung S5PC110
CPU: 1 GHz single-core Hummingbird
GPU: PowerVR SGX540
RAM: 512MB
Weight: 135 g (4.8 oz)
Dimensions: 136 mm (5.3 in) (h)
68 mm (2.67 in) (w)
9 mm (0.352 in) (d)
Screen size: 102 mm (4.0 in)
Resolution: 800×480
Screen density: 233 ppi
Screen type: Super AMOLED or Super-Clear-LCD
Internal storage: 16GB
SD Card: none
Bluetooth: 2.1+EDR
Wi-Fi: 802.11 b/g/n
Main camera: 5MP, flash: LED
Secondary camera: 0.3MP
Power: 1500 mAh internal rechargeable removable lithium-ion battery
Peripherals: A-GPS, NFC, capacitive touchscreen, 3-axis accelerometer, 3-axis gyroscope, digital compass, proximity & light sensors
CM supported: 7, 9, 10, 10.1, 10.2, 11

How to Install CyanogenMod on the Google Nexus S (crespo)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Important Notes

The Nexus S (crespo) is a touchscreen smartphone manufactured by Samsung with direct support from Google. It introduced wireless payment using NFC and Google wallet. It is the second Nexus device.

WARNING:

The newest CM11 Gapps package (20140606) is too big for the /system partition of crespo. Please use the 20140105 package instead.

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to unlock the bootloader:
    fastboot oem unlock
  8. A disclaimer will display on the device that must be accepted. Use the volume keys to cycle through the options. Pressing the power button should confirm your selection.
  9. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked. You can confirm this is the case if you see an unlocked icon at the bottom of the Google boot screen during reboots.
  10. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  2. Download recovery — you can directly download a recovery image using the link below, or visit twrp.me to obtain the latest version of Team Win Recovery Project for your device.
    Recovery: Download
    md5: b1c69e4609a7ac7b86dea6a21411d8c0
  3. Connect the Nexus S to the computer via USB.
  4. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  5. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  6. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  7. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  8. Once the flash completes successfully, reboot the device into recovery to verify the installation. Boot to recovery instructions: Volume Up & Power
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Installing CyanogenMod from recovery

  1. Make sure your computer has working adb.
  2. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  3. Place the CyanogenMod .zip package, as well as any optional .zip packages, on the root of /sdcard:
    • Using adb: adb push filename.zip /sdcard/
    Note: You can copy the .zip packages to your device using any method you are familiar with. The adb method is used here because it is universal across all devices and works in both Android and recovery mode. If you are in recovery mode, you may need to ensure /sdcard (sometimes called Internal Storage) is mounted by checking its status in the Mounts menu. If you have booted regularly, USB debugging must be enabled.
  4. If you are not already in recovery, boot to recovery mode now.
    • Volume Up & Power
  5. In Team Win Recovery Project, select menu choices by tapping on the appropriately labelled button.
  6. Optional (Recommended): Select the Backup button to create a backup.
  7. Select Wipe and then Factory Reset.
  8. Select Install.
  9. Navigate to /sdcard and select the CyanogenMod .zip package.
  10. Follow the on-screen notices to install the package.
  11. Optional: Install any additional packages you wish using the same method (if you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it).
  12. Once installation has finished, return to the main menu and select Reboot, then System. The device will now boot into CyanogenMod.

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For Google Nexus S (crespo)

Introduction

These instructions will hopefully assist you to start with a stock Nexus S, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A Nexus S
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the Nexus S (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Unlocking your Nexus S

What does “unlocking” mean?

Note:

If you’ve already installed CyanogenMod or another ROM on your Nexus S, your device is already unlocked. Assuming you also have adb and fastboot installed on your computer, you can skip this whole section and proceed to the HOW TO BUILD section below.

The first step in putting any custom operating system on your Nexus S is to unlock the bootloader. A bootloader is the very first program that runs when you turn on your device. The bootloader initializes some hardware and then loads the kernel and ramdisk, and gets the boot process going. If the bootloader is in locked mode, it will ensure that only the stock operating system can run. Since you will be installing your own operating system, you need to turn this off. Luckily, Google and samsung make it easy.

Note: A Warning About Unlocking

THE PROCESS OF UNLOCKING THE BOOTLOADER WILL ERASE ALL YOUR PERSONAL DATA FROM THE DEVICE.

Okay. I’m in. What do I need to do this?

To unlock your bootloader, you’ll first need a program on your computer called fastboot. One way to get fastboot is to download and install the Android SDK (Software Developer Kit) from Google. The SDK is used by app developers when they’re writing programs for Android, and who knows, you may want to write apps someday. But the SDK also contains two great tools that are useful even to non-developers. They are:

  • adb – Android Debug Bridge – this is a program that lets your computer “talk” to your Nexus S while the device is running. Among the many things you can do with adb– you can push files from your computer to the device or pull files from the device to your computer, you can get a running real-time log of Android activity (which is very useful for debugging or having others help you debug), you can create an interactive “shell” session (similar to Linux or OS X) to type commands to your device, and much more.

  • fastboot – fastboot works a little bit like adb, except it’s often used at a much earlier point in the boot process, even before Android or any operating system loads. You can put your Nexus S into a “fastboot” mode, whereby, if you are connected via USB cable, you can copy entire partitions from your computer (usually in the form of an image file, such as boot.img or recovery.img) over to the device, wiping over whatever happened to be there. Fastboot is able to do more than that, however. It’s also used to send special commands to the device to do things such as unlock your bootloader.

How do I do the actual unlocking?

So this should be a one time thing…

Install the Android SDK

To unlock your Nexus S, you will need fastboot installed. Go ahead and download the SDK, per the steps on Google’s web page. Then install it by following the specific instructions for your computer.

Note:

Google’s instructions may be out of date for 12.04. The Sun JDK isn’t available anymore as a dpkg AND they say Eclipse 3.6 isn’t available as a package. Well, 3.7.X is now available. Doing a “$ sudo apt-get install eclipse” will now install the proper Eclipse and JDK (OpenJDK 6).

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to unlock the bootloader:
    fastboot oem unlock
  8. A disclaimer will display on the device that must be accepted. Use the volume keys to cycle through the options. Pressing the power button should confirm your selection.unlock the bootloader:
  9. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked. You can confirm this is the case if you see an unlocked icon at the bottom of the Google boot screen during reboots.
  10. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Troubleshooting

If you have issues with fastboot or adb not being found, make sure that the Android SDK folder /platform-tools, which contains the adb and fastboot files, are in the path of execution for commands typed at the terminal. Usually typing something like 

# PATH=$PATH:/your/specific/path/to/android/sdk/platform-tools/

will work for that terminal session.

Note:

The above command requires a bash-like shell. If you’re running a linux distribution which uses a shell such as csh or tcsh, first run /bin/bash to start a bash shell. See http://www.cyberciti.biz/tips/how-do-i-find-out-what-shell-im-using.html or google for more help on that. You will need bash later as well, when using the “. build/envsetup.sh” command.

Note: Linux Mint users

If you have problems with adb (“file not found”) and you’re using 64-bit linux (I don’t know much about Mint, so maybe it’s all 64-bit?) try doing this to see if adb works better: 

$ sudo apt-get install ia32-libs

You’ll be using fastboot again to install a custom recovery.

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b cm-13.0

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast crespo

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast crespo

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your Nexus S is connected to your computer via the USB cable and that you are in the ~/android/system/device/samsung/crespo directory (you can cd ~/android/system/device/samsung/crespo if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/samsung directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly. Nexus users: While it maybe be tempting to run the script on stock Android, and in fact it may succeed, realize that some of the blobs CyanogenMod uses are modified or otherwise different from stock blobs (e.g. Adreno graphics libraries). Save yourself some trouble and install a copy of CyanogenMod on your device before extracting blobs.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/samsung directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch crespo

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make crespo should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/crespo/cm_crespo-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-13.0-20161224-UNOFFICIAL-crespo.zip, which is the CyanogenMod installation package.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  1. Connect the Nexus S to the computer via USB.
  2. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  3. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  4. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  5. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  6. Once the flash completes successfully, reboot the device into recovery to verify the installation.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-13.0-20161224-UNOFFICIAL-crespo.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

Samsung Galaxy Mini (tass)

Cyanogenmod ROM Samsung Galaxy Mini (tass)

Cyanogenmod ROM Samsung Galaxy Mini (tass)

Quick Info

Download CyanogenMod

Download (nightly build)
CyanogenMod 7 (Android 2.3 (Gingerbread))

Note: Support Status

This device does not support the latest official release of CyanogenMod. This may be due to hardware limitations or simply because development is ongoing. The most recent version supported is based on the gingerbread branch of CyanogenMod.

Notes

The official Android 2.3 update from Samsung must be applied before following this guide. This guide applies to GT-S5570 aka tass, not any other variant. If your device is GT-S5570i or any of the i variants (aka tassve), your phone is not supported by official cyanogenmod, so check the Unofficial Ports section instead!

Special boot modes

  • Recovery: Home & Power

Source code

Device http://www.github.com/cyanogenmod/android_device_samsung_tass
Galaxy Mini Specifications
Codename: tass
Vendor: Samsung
Manufacturer: samsung
Release date: 2011 January (INT)
Type: phone
GSM freq: Quad-band GSM 850 900 1800 1900 MHz GPRS/EDGE

Dual-band 900 2100 MHz HSPA/WCDMA HSPA+

Platform: Qualcomm MSM7227
CPU: 600 MHz single-core ARM11
GPU: Adreno 200
RAM: 384MB
Weight: 113 g (4.0 oz)
Dimensions: 110 mm (4.3 in) (h)
61 mm (2.40 in) (w)
12 mm (0.476 in) (d)
Screen size: 79 mm (3.1 in)
Resolution: 320×240
Screen density: 127 ppi
Screen type: TFT LCD
Internal storage: 160MB
SD Card: up to 32GB
Bluetooth: 2.1
Wi-Fi: 802.11 b/g/n
Main camera: 3MP
Power: 1200 mAh
Peripherals: capacitive touchscreen, proximity sensor, 3-axis accelerometer
CM supported: 7
Latest CM version: gingerbread

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

WARNING:

The procedure described in the article below is intended for the S5570 (Pop / Mini) and WILL NOT WORK ON THE S5570i (Pop Plus / Mini).
For S5570i users only: to root your phone and install ClockworkMod Recovery see this TeamAndroid article. There are NO OFFICIAL CYANOGENMOD FIRMWARES FOR THE S5570i; see the XDA forum for actively developed 3rd-party firmwares.

Installing a Custom Recovery

If the Samsung Galaxy Mini already has the ClockworkMod Recovery installed, skip this section.

NOTE: These instructions only work for a Windows PC. The procedure described below is intended for the S5570 (Mini / Pop) and WILL NOT WORK ON THE S5570i (Mini / Pop Plus).

  1. Download the ClockworkMod Recovery kernel, Odin v4.38, and TASS.ops
    • Recovery kernel for Galaxy Mini: download
      md5: 3fd524fa71d1bfff337d65daea6035f4
    • Odin v4.38 for Galaxy Mini: download
      md5: 913d562312fcaf72528f59d4566975d4
    • TASS.ops for Galaxy Mini: download
      md5: d1cfd906d34843e5c98b6cb6a7d6fcc3
  2. Open Odin v4.38.
  3. Power off the Galaxy Mini and connect the microUSB to the computer, but not the Galaxy Mini.
  4. Boot the Galaxy Mini into download mode by holding Volume Down, Home, & Power.
  5. Connect the microUSB cable from the computer to the Galaxy Mini.
  6. Wait for Odin to recognize the Galaxy Mini (the box in the top left will turn yellow and say (COM #) where # is a random number).
  7. Ensure One Package is checked right below that box.
  8. Select TASS.ops by pressing the OPS button.
  9. Select tass-recovery-cwm.tar by pressing the One Package button.
  10. Press Start and wait until the phone reboots.
  11. The Galaxy Mini now has the ClockworkMod Recovery installed. Continue to the next section.

Installing CyanogenMod from recovery

  1. Make sure your computer has working adb.
  2. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  3. Boot to recovery mode, and connect the phone to your computer through USB.
    • Home & Power
  4. In ClockworkMod Recovery, use the physical volume buttons to move up and down. On most devices, the power button is used to confirm a menu selection, but for some devices a physical home key acts as a selector. Some devices have touch enabled ClockworkMod Recovery, in which case you may be able to swipe to, or touch, menu selections.
  5. Optional (Recommended): Select backup and restore to create a backup.
  6. Select wipe data/factory reset.
  7. You have two options for transferring and installing the installation packages. The sideload method is more universal across devices, whereas the push and install method is more commonly used:
    • Sideload method: select install zip > install zip from sideload. Follow the on-screen notices to install the package. The installer does not necessarily display an “Install complete.” message. You can tell the install is complete if there were no fatal error messages and you have regained control over the menu.
    • Push and install method: Open a command prompt (or Terminal on Mac and Linux) and navigate to the directory holding the package(s) you would like to install. On the device, navigate to the mounts and storage menu. If you see /storage/sdcard0 or /sdcard as a mountable volume, go ahead and mount it. If you do not see one of these partitions, then instead mount the /data partition. Take note of which volume you mounted. Now, push the package(s) to your device (also, see tip below):
    – If you mounted /storage/sdcard0, then: adb push update.zip /storage/sdcard0/
    – If you mounted /sdcard or /data, then: adb push update.zip /sdcard/
    where update.zip should be replaced with the package filename. Go back to the main menu and select install zip. Choose to install from the same directory where you pushed the package(s). If you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it.
  8. Once installation has finished, return to the main menu and select reboot system now. The device will now boot into CyanogenMod.

Helpful Tip – SD card folders

CyanogenMod 10.1 and newer have multi-user support (introduced in Android 4.2). If your device has storage on the /data partition, then Android actually looks in /data/media/0/ for the first user’s /sdcard/ storage. ClockworkMod recovery symlinks /sdcard/ to /data/media/ though. So, if you are pushing files to internal storage in recovery and want them to be visible in Android, you should push them to /sdcard/0/ or /data/media/0/. Here’s the most frequent scenarios:

  1. If you’re coming from a ROM with Android 4.1 or older to CyanogenMod 10 or older: adb push update.zip /sdcard/
  2. If you’re coming from a ROM with Android 4.1 or older to CyanogenMod 10.1 or newer: adb shell "mkdir /sdcard/0/" followed by adb push update.zip /sdcard/0/
  3. If you’re coming from a ROM with Android 4.2 or newer to CyanogenMod 10.1 or newer: adb push update.zip /sdcard/0/

How To Build CyanogenMod For Samsung Galaxy Mini (tass)

Introduction

These instructions will hopefully assist you to start with a stock Galaxy Mini, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A Galaxy Mini
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the Galaxy Mini (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b gingerbread

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt Rom Manager

$ cd ~/android/system/vendor/cyanogen

then enter: 

$ ./get-rommanager

You won’t see any confirmation- just another prompt. But this should cause the Rom Manager apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type:

$ source build/envsetup.sh
$ lunch

You should see a list of devices, including something like cm_tass-userdebug. Select it by typing its number. It is possible that lunch does not display your device. In that case try 

$ lunch cm_tass-userdebug

or 

$ lunch full_tass-userdebug

If all goes well, you should see that tass-specific directories are downloaded automatically.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your Galaxy Mini is connected to your computer via the USB cable and that you are in the ~/android/system/device/samsung/tass directory (you can cd ~/android/system/device/samsung/tass if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/samsung directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/samsung directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilt/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch tass

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make tass should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/tass/cm_tass-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-7-20161224-UNOFFICIAL-tass.zip, which is the CyanogenMod installation package.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-7-20161224-UNOFFICIAL-tass.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

OnePlus One (bacon)

Cyanogenmod ROM OnePlus One (bacon)

Cyanogenmod ROM OnePlus One (bacon)

Quick Info

Check out OnePlus One (“bacon”) with newer LineageOS software

LineageOS

Download CyanogenMod

Download (xnph25r build)
CyanogenMod 11.0 (Android 4.4-4.4.4 (KitKat))

Download (build1 build)
CyanogenMod 13 (Android 6.0/6.0.1 (Marshmallow))

Download (znh5yao3xh build)
CyanogenMod 13.0 (Android 6.0/6.0.1 (Marshmallow))

Download (nightly build)
CyanogenMod 14.1 (Android 7.1 (Nougat))

Notes

Note: Officially supported by Cyanogen Inc.

The OnePlus One is officially supported by Cyanogen Inc. Factory images can be found at cyngn.com/support/

Special boot modes

  • Recovery: With the device powered down, hold the Volume Down and Power buttons.
  • Fastboot: With the device powered down, hold the Volume Up and Power buttons.

Source code

Device http://www.github.com/cyanogenmod/android_device_oneplus_bacon
Kernel http://www.github.com/cyanogenmod/android_kernel_oneplus_msm8974
One Specifications
Codename: bacon
Also known as: OPO
Vendor: OnePlus
Release date: 2014 June 6
Type: phone
GSM freq: 850 900 1800 1900 MHz UMTS
LTE freq: 700 1700/2100 1800 2100 2600 FDD
Platform: Qualcomm Snapdragon 801
CPU: 2.5 GHz quad-core Krait 400
GPU: Adreno 330
RAM: 3GB
Weight: 162 g
Dimensions: 152.9 mm (h)
75.9 mm (w)
8.9 mm (d)
Screen size: 139.7 mm (5.5 in)
Resolution: 1920×1080
Screen density: 401 ppi
Screen type: JDI IPS
Internal storage: 16GB, 64GB
SD Card: none
Bluetooth: 4.1
Wi-Fi: 802.11 2.4GHz b/g/n 5GHz n/ac
Main camera: 13MP F/2.0, flash: Dual LED
Secondary camera: 5MP
Power: 3100 mAh
Peripherals: Wi-Fi Direct, Wi-Fi Display, Wi-Fi Hotspot, GPS, NFC, Light sensor, Proximity Sensor
CM supported: 11, 12, 12.1, 13, 14.1

How to Install CyanogenMod on the OnePlus One (bacon)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Important Notes

Note: Officially supported by Cyanogen Inc.

The OnePlus One is officially supported by Cyanogen Inc. Factory images can be found at cyngn.com/support/

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to unlock the bootloader:
    fastboot oem unlock
  8. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked.
  9. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  2. Download recovery — you can directly download a recovery image using the link below, or visit twrp.me to obtain the latest version of Team Win Recovery Project for your device.
    Recovery: Download
    md5: 57da36526b6666640317cd5f404717d1
  3. Connect the One to the computer via USB.
  4. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  5. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  6. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  7. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  8. Once the flash completes successfully, reboot the device into recovery to verify the installation. Boot to recovery instructions: With the device powered down, hold the Volume Down and Power buttons.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Installing CyanogenMod from recovery

  1. Make sure your computer has working adb.
  2. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  3. Place the CyanogenMod .zip package, as well as any optional .zip packages, on the root of /sdcard:
    • Using adb: adb push filename.zip /sdcard/
    Note: You can copy the .zip packages to your device using any method you are familiar with. The adb method is used here because it is universal across all devices and works in both Android and recovery mode. If you are in recovery mode, you may need to ensure /sdcard (sometimes called Internal Storage) is mounted by checking its status in the Mounts menu. If you have booted regularly, USB debugging must be enabled.
  4. If you are not already in recovery, boot to recovery mode now.
    • With the device powered down, hold the Volume Down and Power buttons.
  5. In Team Win Recovery Project, select menu choices by tapping on the appropriately labelled button.
  6. Optional (Recommended): Select the Backup button to create a backup.
  7. Select Wipe and then Factory Reset.
  8. Select Install.
  9. Navigate to /sdcard and select the CyanogenMod .zip package.
  10. Follow the on-screen notices to install the package.
  11. Optional: Install any additional packages you wish using the same method (if you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it).
  12. Once installation has finished, return to the main menu and select Reboot, then System. The device will now boot into CyanogenMod.

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For OnePlus One (bacon)

Introduction

These instructions will hopefully assist you to start with a stock One, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A One
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the One (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Unlocking your One

What does “unlocking” mean?

Note:

If you’ve already installed CyanogenMod or another ROM on your One, your device is already unlocked. Assuming you also have adb and fastboot installed on your computer, you can skip this whole section and proceed to the HOW TO BUILD section below.

The first step in putting any custom operating system on your One is to unlock the bootloader. A bootloader is the very first program that runs when you turn on your device. The bootloader initializes some hardware and then loads the kernel and ramdisk, and gets the boot process going. If the bootloader is in locked mode, it will ensure that only the stock operating system can run. Since you will be installing your own operating system, you need to turn this off. Luckily, Google and oneplus make it easy.

Note: A Warning About Unlocking

THE PROCESS OF UNLOCKING THE BOOTLOADER WILL ERASE ALL YOUR PERSONAL DATA FROM THE DEVICE.

Okay. I’m in. What do I need to do this?

To unlock your bootloader, you’ll first need a program on your computer called fastboot. One way to get fastboot is to download and install the Android SDK (Software Developer Kit) from Google. The SDK is used by app developers when they’re writing programs for Android, and who knows, you may want to write apps someday. But the SDK also contains two great tools that are useful even to non-developers. They are:

  • adb – Android Debug Bridge – this is a program that lets your computer “talk” to your One while the device is running. Among the many things you can do with adb– you can push files from your computer to the device or pull files from the device to your computer, you can get a running real-time log of Android activity (which is very useful for debugging or having others help you debug), you can create an interactive “shell” session (similar to Linux or OS X) to type commands to your device, and much more.

  • fastboot – fastboot works a little bit like adb, except it’s often used at a much earlier point in the boot process, even before Android or any operating system loads. You can put your One into a “fastboot” mode, whereby, if you are connected via USB cable, you can copy entire partitions from your computer (usually in the form of an image file, such as boot.img or recovery.img) over to the device, wiping over whatever happened to be there. Fastboot is able to do more than that, however. It’s also used to send special commands to the device to do things such as unlock your bootloader.

How do I do the actual unlocking?

So this should be a one time thing…

Install the Android SDK

To unlock your One, you will need fastboot installed. Go ahead and download the SDK, per the steps on Google’s web page. Then install it by following the specific instructions for your computer.

Note:

Google’s instructions may be out of date for 12.04. The Sun JDK isn’t available anymore as a dpkg AND they say Eclipse 3.6 isn’t available as a package. Well, 3.7.X is now available. Doing a “$ sudo apt-get install eclipse” will now install the proper Eclipse and JDK (OpenJDK 6).

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to unlock the bootloader:
    fastboot oem unlock
  8. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked.
  9. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Troubleshooting

If you have issues with fastboot or adb not being found, make sure that the Android SDK folder /platform-tools, which contains the adb and fastboot files, are in the path of execution for commands typed at the terminal. Usually typing something like 

# PATH=$PATH:/your/specific/path/to/android/sdk/platform-tools/

will work for that terminal session.

Note:

The above command requires a bash-like shell. If you’re running a linux distribution which uses a shell such as csh or tcsh, first run /bin/bash to start a bash shell. See http://www.cyberciti.biz/tips/how-do-i-find-out-what-shell-im-using.html or google for more help on that. You will need bash later as well, when using the “. build/envsetup.sh” command.

Note: Linux Mint users

If you have problems with adb (“file not found”) and you’re using 64-bit linux (I don’t know much about Mint, so maybe it’s all 64-bit?) try doing this to see if adb works better: 

$ sudo apt-get install ia32-libs

You’ll be using fastboot again to install a custom recovery.

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b cm-13.0

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast bacon

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast bacon

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your One is connected to your computer via the USB cable and that you are in the ~/android/system/device/oneplus/bacon directory (you can cd ~/android/system/device/oneplus/bacon if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/oneplus directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/oneplus directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch bacon

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make bacon should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/bacon/cm_bacon-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-13.0-20161224-UNOFFICIAL-bacon.zip, which is the CyanogenMod installation package.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  1. Connect the One to the computer via USB.
  2. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  3. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  4. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  5. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  6. Once the flash completes successfully, reboot the device into recovery to verify the installation.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-13.0-20161224-UNOFFICIAL-bacon.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.