admin

HTC One A9 (hiaeuhl)

CyanogenMod ROM HTC One A9 (hiaeuhl) (GSM International)

CyanogenMod ROM HTC One A9 (GSM International) (hiaeuhl)

Quick Info

Check out HTC One A9 (GSM International) (“hiaeuhl”) with newer LineageOS software

LineageOS

Download CyanogenMod

Download (nightly build)
CyanogenMod 14.1 (Android 7.1 (Nougat))

Special boot modes

  • Recovery: With the device powered down, hold the Volume Down and Power buttons until HBOOT appears, then release the buttons. Navigate using the volume keys and select RECOVERY using the Power key.
  • Bootloader: With the device powered down, hold the Volume Down and Power buttons until HBOOT appears, then release the buttons.
  • Fastboot: With the device powered down, hold the Volume Down and Power buttons until HBOOT appears, then release the buttons. Navigate using the volume keys and select FASTBOOT using the Power key.

Source code

Device http://www.github.com/cyanogenmod/android_device_htc_hiaeuhl
Kernel http://www.github.com/cyanogenmod/android_kernel_htc_msm8952
One A9 (GSM International) Specifications
Codename: hiaeuhl
Vendor: HTC
Release date: 2015 November
Type: phone
Platform: Qualcomm MSM8952 Snapdragon 617
CPU: 4 x 1.5 GHz, 4 x 1.2 GHz octa-core Cortex A53
GPU: Adreno 405
RAM: 2/3GB
Weight: 143 g (5.04 oz)
Dimensions: 145.8 x 70.8 x 7.3 mm (5.74 x 2.79 x 0.29 in)
Screen size: 127 mm (5.0 in)
Resolution: 1080×1920
Screen density: 441 ppi
Screen type: AMOLED
Internal storage: 16/32GB
SD Card: up to 2TB
Bluetooth: 4.1
Wi-Fi: 802.11 a/b/g/n/ac (2.4 & 5 GHz)
Main camera: 13MP, flash: dual-LED
Secondary camera: 4MP
Power: 2150 mAh, Quick Charge 2.0
CM supported: 13, 14.1

How to Install CyanogenMod on the HTC One A9 (GSM International) (hiaeuhl)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

Note:

The One A9 (GSM International) can be unlocked officially via the HTC Dev unlock program. This unlock method may have certain restrictions, such as not being able to flash a kernel via recovery (no longer applicable to 2013+ released HTC devices) or no USB access to sdcard in recovery. Some devices, however, have no other method to install custom firmware.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to obtain your bootloader unlock token:
    fastboot oem get_identifier_token
  8. Visit the HTCDev Bootloader Unlock website and follow the instructions there to obtain your unlock key and unlock your bootloader. If your device does not appear in the drop-down list, select All Other Supported Models.
  9. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked.
  10. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  2. Download recovery — you can directly download a recovery image using the link below, or visit twrp.me to obtain the latest version of Team Win Recovery Project for your device.
    Recovery: Download
    md5: beaefd4f6baadfb375ad67001a78c6d8
  3. Connect the One A9 (GSM International) to the computer via USB.
  4. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  5. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  6. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  7. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  8. Once the flash completes successfully, reboot the device into recovery to verify the installation. Boot to recovery instructions: With the device powered down, hold the Volume Down and Power buttons until HBOOT appears, then release the buttons. Navigate using the volume keys and select RECOVERY using the Power key.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Installing CyanogenMod from recovery

  1. Make sure your computer has working adb.
  2. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  3. Place the CyanogenMod .zip package, as well as any optional .zip packages, on the root of /sdcard:
    • Using adb: adb push filename.zip /sdcard/
    Note: You can copy the .zip packages to your device using any method you are familiar with. The adb method is used here because it is universal across all devices and works in both Android and recovery mode. If you are in recovery mode, you may need to ensure /sdcard (sometimes called Internal Storage) is mounted by checking its status in the Mounts menu. If you have booted regularly, USB debugging must be enabled.
  4. If you are not already in recovery, boot to recovery mode now.
    • With the device powered down, hold the Volume Down and Power buttons until HBOOT appears, then release the buttons. Navigate using the volume keys and select RECOVERY using the Power key.
  5. In Team Win Recovery Project, select menu choices by tapping on the appropriately labelled button.
  6. Optional (Recommended): Select the Backup button to create a backup.
  7. Select Wipe and then Factory Reset.
  8. Select Install.
  9. Navigate to /sdcard and select the CyanogenMod .zip package.
  10. Follow the on-screen notices to install the package.
  11. Optional: Install any additional packages you wish using the same method (if you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it).
  12. Once installation has finished, return to the main menu and select Reboot, then System. The device will now boot into CyanogenMod.

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For HTC One A9 (GSM International) (hiaeuhl)

Introduction

These instructions will hopefully assist you to start with a stock One A9 (GSM International), unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A One A9 (GSM International)
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the One A9 (GSM International) (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b cm-13.0

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast hiaeuhl

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast hiaeuhl

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your One A9 (GSM International) is connected to your computer via the USB cable and that you are in the ~/android/system/device/htc/hiaeuhl directory (you can cd ~/android/system/device/htc/hiaeuhl if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/htc directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/htc directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch hiaeuhl

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make hiaeuhl should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/hiaeuhl/cm_hiaeuhl-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-13.0-20161224-UNOFFICIAL-hiaeuhl.zip, which is the CyanogenMod installation package.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  1. Connect the One A9 (GSM International) to the computer via USB.
  2. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  3. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  4. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  5. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  6. Once the flash completes successfully, reboot the device into recovery to verify the installation.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-13.0-20161224-UNOFFICIAL-hiaeuhl.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

Categories HTC

Google Android One (sprout8) (8GB)

CyanogenMod ROM Android One (sprout8) (8GB)

CyanogenMod ROM Android One (sprout8) (8GB)

Quick Info

Download CyanogenMod

It looks like we don’t have any roms for download for this device. 🙁

Special boot modes

  • Recovery: Volume Up & Power. In the menu use Volume Up to navigate to “Recovery Mode” option and Volume Down to select.
  • Fastboot: Volume Up & Power. In the menu use Volume Up to navigate to “Fastboot Mode” option and Volume Down to select.

Source code

Device http://www.github.com/cyanogenmod/android_device_google_sprout8
Kernel http://www.github.com/cyanogenmod/android_kernel_mediatek_sprout
Android One 2014 Specifications
Codename: sprout8
Vendor: Google
Manufacturer: Micromax-Karbonn-Spice
Release date: 2014 September
Type: phone
Platform: MediaTek MT6582
CPU: 1.3 GHz quad-core Cortex-A7
GPU: Mali-400MP2
RAM: 1GB
Screen size: 114 mm (4.5 in)
Screen density: 220 ppi (preferably 200 0r 190)
Screen type: IPS
Internal storage: 8GB
SD Card: up to 32GB
Bluetooth: 4.0
Main camera: 4.9 MP
Secondary camera: 1.9MP
Power: 1700mAh L
CM supported: 12.1, 13

How to Install CyanogenMod on the Google Android One 2014 (sprout8)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to unlock the bootloader:
    fastboot oem unlock
  8. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked.
  9. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  2. Download recovery — visit twrp.me to obtain the latest version of Team Win Recovery Project for your device.
  3. Connect the Android One 2014 to the computer via USB.
  4. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  5. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  6. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  7. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  8. Once the flash completes successfully, reboot the device into recovery to verify the installation. Boot to recovery instructions: Volume Up & Power. In the menu use Volume Up to navigate to “Recovery Mode” option and Volume Down to select.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Installing CyanogenMod from recovery

  1. Make sure your computer has working adb.
  2. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  3. Place the CyanogenMod .zip package, as well as any optional .zip packages, on the root of /sdcard:
    • Using adb: adb push filename.zip /sdcard/
    Note: You can copy the .zip packages to your device using any method you are familiar with. The adb method is used here because it is universal across all devices and works in both Android and recovery mode. If you are in recovery mode, you may need to ensure /sdcard (sometimes called Internal Storage) is mounted by checking its status in the Mounts menu. If you have booted regularly, USB debugging must be enabled.
  4. If you are not already in recovery, boot to recovery mode now.
    • Volume Up & Power. In the menu use Volume Up to navigate to “Recovery Mode” option and Volume Down to select.
  5. In Team Win Recovery Project, select menu choices by tapping on the appropriately labelled button.
  6. Optional (Recommended): Select the Backup button to create a backup.
  7. Select Wipe and then Factory Reset.
  8. Select Install.
  9. Navigate to /sdcard and select the CyanogenMod .zip package.
  10. Follow the on-screen notices to install the package.
  11. Optional: Install any additional packages you wish using the same method (if you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it).
  12. Once installation has finished, return to the main menu and select Reboot, then System. The device will now boot into CyanogenMod.

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For Google Android One 2014 (sprout8)

Introduction

These instructions will hopefully assist you to start with a stock Android One 2014, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A Android One 2014
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the Android One 2014 (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Unlocking your Android One 2014

What does “unlocking” mean?

Note:

If you’ve already installed CyanogenMod or another ROM on your Android One 2014, your device is already unlocked. Assuming you also have adb and fastboot installed on your computer, you can skip this whole section and proceed to the HOW TO BUILD section below.

The first step in putting any custom operating system on your Android One 2014 is to unlock the bootloader. A bootloader is the very first program that runs when you turn on your device. The bootloader initializes some hardware and then loads the kernel and ramdisk, and gets the boot process going. If the bootloader is in locked mode, it will ensure that only the stock operating system can run. Since you will be installing your own operating system, you need to turn this off. Luckily, Google and google make it easy.

Note: A Warning About Unlocking

THE PROCESS OF UNLOCKING THE BOOTLOADER WILL ERASE ALL YOUR PERSONAL DATA FROM THE DEVICE.

Okay. I’m in. What do I need to do this?

To unlock your bootloader, you’ll first need a program on your computer called fastboot. One way to get fastboot is to download and install the Android SDK (Software Developer Kit) from Google. The SDK is used by app developers when they’re writing programs for Android, and who knows, you may want to write apps someday. But the SDK also contains two great tools that are useful even to non-developers. They are:

  • adb – Android Debug Bridge – this is a program that lets your computer “talk” to your Android One 2014 while the device is running. Among the many things you can do with adb– you can push files from your computer to the device or pull files from the device to your computer, you can get a running real-time log of Android activity (which is very useful for debugging or having others help you debug), you can create an interactive “shell” session (similar to Linux or OS X) to type commands to your device, and much more.

  • fastboot – fastboot works a little bit like adb, except it’s often used at a much earlier point in the boot process, even before Android or any operating system loads. You can put your Android One 2014 into a “fastboot” mode, whereby, if you are connected via USB cable, you can copy entire partitions from your computer (usually in the form of an image file, such as boot.img or recovery.img) over to the device, wiping over whatever happened to be there. Fastboot is able to do more than that, however. It’s also used to send special commands to the device to do things such as unlock your bootloader.

How do I do the actual unlocking?

So this should be a one time thing…

Install the Android SDK

To unlock your Android One 2014, you will need fastboot installed. Go ahead and download the SDK, per the steps on Google’s web page. Then install it by following the specific instructions for your computer.

Note:

Google’s instructions may be out of date for 12.04. The Sun JDK isn’t available anymore as a dpkg AND they say Eclipse 3.6 isn’t available as a package. Well, 3.7.X is now available. Doing a “$ sudo apt-get install eclipse” will now install the proper Eclipse and JDK (OpenJDK 6).

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to unlock the bootloader:
    fastboot oem unlock
  8. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked.
  9. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Troubleshooting

If you have issues with fastboot or adb not being found, make sure that the Android SDK folder /platform-tools, which contains the adb and fastboot files, are in the path of execution for commands typed at the terminal. Usually typing something like 

# PATH=$PATH:/your/specific/path/to/android/sdk/platform-tools/

will work for that terminal session.

Note:

The above command requires a bash-like shell. If you’re running a linux distribution which uses a shell such as csh or tcsh, first run /bin/bash to start a bash shell. See http://www.cyberciti.biz/tips/how-do-i-find-out-what-shell-im-using.html or google for more help on that. You will need bash later as well, when using the “. build/envsetup.sh” command.

Note: Linux Mint users

If you have problems with adb (“file not found”) and you’re using 64-bit linux (I don’t know much about Mint, so maybe it’s all 64-bit?) try doing this to see if adb works better: 

$ sudo apt-get install ia32-libs

You’ll be using fastboot again to install a custom recovery.

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b cm-13.0

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast sprout8

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast sprout8

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your Android One 2014 is connected to your computer via the USB cable and that you are in the ~/android/system/device/google/sprout8 directory (you can cd ~/android/system/device/google/sprout8 if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/google directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/google directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch sprout8

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make sprout8 should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/sprout8/cm_sprout8-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-13.0-20161224-UNOFFICIAL-sprout8.zip, which is the CyanogenMod installation package.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  1. Connect the Android One 2014 to the computer via USB.
  2. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  3. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  4. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  5. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  6. Once the flash completes successfully, reboot the device into recovery to verify the installation.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-13.0-20161224-UNOFFICIAL-sprout8.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

Google Android One (sprout4)

CyanogenMod ROM Android One (sprout4) 4GB (Micromax-Karbonn-Spice)

CyanogenMod ROM Android One 4GB (Micromax-Karbonn-Spice) (sprout4)

Quick Info

Download CyanogenMod

It looks like we don’t have any roms for download for this device. 🙁

Special boot modes

  • Recovery: Volume Up & Power. In the menu use Volume Up to navigate to “Recovery Mode” option and Volume Down to select.
  • Fastboot: Volume Up & Power. In the menu use Volume Up to navigate to “Fastboot Mode” option and Volume Down to select.

Source code

Device http://www.github.com/cyanogenmod/android_device_google_sprout4
Kernel http://www.github.com/cyanogenmod/android_kernel_mediatek_sprout
Android One 2014 Specifications
Codename: sprout4
Vendor: Google
Manufacturer: Micromax-Karbonn-Spice
Release date: 2014 September
Type: phone
Platform: MediaTek MT6582
CPU: 1.3 GHz quad-core Cortex-A7
GPU: Mali-400MP2
RAM: 1GB
Screen size: 114 mm (4.5 in)
Screen density: 220 ppi (preferably 200 0r 190)
Screen type: IPS
Internal storage: 4GB
SD Card: up to 32GB
Bluetooth: 4.0
Main camera: 4.9 MP
Secondary camera: 1.9MP
Power: 1700mAh L
CM supported: 12.1, 13

How to Install CyanogenMod on the Google Android One 2014 (sprout4)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to unlock the bootloader:
    fastboot oem unlock
  8. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked.
  9. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  2. Download recovery — visit twrp.me to obtain the latest version of Team Win Recovery Project for your device.
  3. Connect the Android One 2014 to the computer via USB.
  4. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  5. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  6. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  7. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  8. Once the flash completes successfully, reboot the device into recovery to verify the installation. Boot to recovery instructions: Volume Up & Power. In the menu use Volume Up to navigate to “Recovery Mode” option and Volume Down to select.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Installing CyanogenMod from recovery

  1. Make sure your computer has working adb.
  2. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  3. Place the CyanogenMod .zip package, as well as any optional .zip packages, on the root of /sdcard:
    • Using adb: adb push filename.zip /sdcard/
    Note: You can copy the .zip packages to your device using any method you are familiar with. The adb method is used here because it is universal across all devices and works in both Android and recovery mode. If you are in recovery mode, you may need to ensure /sdcard (sometimes called Internal Storage) is mounted by checking its status in the Mounts menu. If you have booted regularly, USB debugging must be enabled.
  4. If you are not already in recovery, boot to recovery mode now.
    • Volume Up & Power. In the menu use Volume Up to navigate to “Recovery Mode” option and Volume Down to select.
  5. In Team Win Recovery Project, select menu choices by tapping on the appropriately labelled button.
  6. Optional (Recommended): Select the Backup button to create a backup.
  7. Select Wipe and then Factory Reset.
  8. Select Install.
  9. Navigate to /sdcard and select the CyanogenMod .zip package.
  10. Follow the on-screen notices to install the package.
  11. Optional: Install any additional packages you wish using the same method (if you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it).
  12. Once installation has finished, return to the main menu and select Reboot, then System. The device will now boot into CyanogenMod.

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For Google Android One 2014 (sprout4)

Introduction

These instructions will hopefully assist you to start with a stock Android One 2014, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A Android One 2014
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the Android One 2014 (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Unlocking your Android One 2014

What does “unlocking” mean?

Note:

If you’ve already installed CyanogenMod or another ROM on your Android One 2014, your device is already unlocked. Assuming you also have adb and fastboot installed on your computer, you can skip this whole section and proceed to the HOW TO BUILD section below.

The first step in putting any custom operating system on your Android One 2014 is to unlock the bootloader. A bootloader is the very first program that runs when you turn on your device. The bootloader initializes some hardware and then loads the kernel and ramdisk, and gets the boot process going. If the bootloader is in locked mode, it will ensure that only the stock operating system can run. Since you will be installing your own operating system, you need to turn this off. Luckily, Google and google make it easy.

Note: A Warning About Unlocking

THE PROCESS OF UNLOCKING THE BOOTLOADER WILL ERASE ALL YOUR PERSONAL DATA FROM THE DEVICE.

Okay. I’m in. What do I need to do this?

To unlock your bootloader, you’ll first need a program on your computer called fastboot. One way to get fastboot is to download and install the Android SDK (Software Developer Kit) from Google. The SDK is used by app developers when they’re writing programs for Android, and who knows, you may want to write apps someday. But the SDK also contains two great tools that are useful even to non-developers. They are:

  • adb – Android Debug Bridge – this is a program that lets your computer “talk” to your Android One 2014 while the device is running. Among the many things you can do with adb– you can push files from your computer to the device or pull files from the device to your computer, you can get a running real-time log of Android activity (which is very useful for debugging or having others help you debug), you can create an interactive “shell” session (similar to Linux or OS X) to type commands to your device, and much more.

  • fastboot – fastboot works a little bit like adb, except it’s often used at a much earlier point in the boot process, even before Android or any operating system loads. You can put your Android One 2014 into a “fastboot” mode, whereby, if you are connected via USB cable, you can copy entire partitions from your computer (usually in the form of an image file, such as boot.img or recovery.img) over to the device, wiping over whatever happened to be there. Fastboot is able to do more than that, however. It’s also used to send special commands to the device to do things such as unlock your bootloader.

How do I do the actual unlocking?

So this should be a one time thing…

Install the Android SDK

To unlock your Android One 2014, you will need fastboot installed. Go ahead and download the SDK, per the steps on Google’s web page. Then install it by following the specific instructions for your computer.

Note:

Google’s instructions may be out of date for 12.04. The Sun JDK isn’t available anymore as a dpkg AND they say Eclipse 3.6 isn’t available as a package. Well, 3.7.X is now available. Doing a “$ sudo apt-get install eclipse” will now install the proper Eclipse and JDK (OpenJDK 6).

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to unlock the bootloader:
    fastboot oem unlock
  8. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked.
  9. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Troubleshooting

If you have issues with fastboot or adb not being found, make sure that the Android SDK folder /platform-tools, which contains the adb and fastboot files, are in the path of execution for commands typed at the terminal. Usually typing something like 

# PATH=$PATH:/your/specific/path/to/android/sdk/platform-tools/

will work for that terminal session.

Note:

The above command requires a bash-like shell. If you’re running a linux distribution which uses a shell such as csh or tcsh, first run /bin/bash to start a bash shell. See http://www.cyberciti.biz/tips/how-do-i-find-out-what-shell-im-using.html or google for more help on that. You will need bash later as well, when using the “. build/envsetup.sh” command.

Note: Linux Mint users

If you have problems with adb (“file not found”) and you’re using 64-bit linux (I don’t know much about Mint, so maybe it’s all 64-bit?) try doing this to see if adb works better: 

$ sudo apt-get install ia32-libs

You’ll be using fastboot again to install a custom recovery.

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b cm-13.0

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast sprout4

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast sprout4

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your Android One 2014 is connected to your computer via the USB cable and that you are in the ~/android/system/device/google/sprout4 directory (you can cd ~/android/system/device/google/sprout4 if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/google directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/google directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch sprout4

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make sprout4 should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/sprout4/cm_sprout4-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-13.0-20161224-UNOFFICIAL-sprout4.zip, which is the CyanogenMod installation package.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  1. Connect the Android One 2014 to the computer via USB.
  2. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  3. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  4. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  5. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  6. Once the flash completes successfully, reboot the device into recovery to verify the installation.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-13.0-20161224-UNOFFICIAL-sprout4.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

HTC One A9 (hiaeul)

CyanogenMod ROM HTC One A9 (hiaeul) (GSM US)

CyanogenMod ROM HTC One A9 (GSM US) (hiaeul)

Quick Info

Check out HTC One A9 (GSM US) (“hiaeul”) with newer LineageOS software

LineageOS

Download CyanogenMod

Download (nightly build)
CyanogenMod 14.1 (Android 7.1 (Nougat))

Special boot modes

  • Recovery: With the device powered down, hold the Volume Down and Power buttons until HBOOT appears, then release the buttons. Navigate using the volume keys and select RECOVERY using the Power key.
  • Bootloader: With the device powered down, hold the Volume Down and Power buttons until HBOOT appears, then release the buttons.
  • Fastboot: With the device powered down, hold the Volume Down and Power buttons until HBOOT appears, then release the buttons. Navigate using the volume keys and select FASTBOOT using the Power key.

Source code

Device http://www.github.com/cyanogenmod/android_device_htc_hiaeul
Kernel http://www.github.com/cyanogenmod/android_kernel_htc_msm8952
One A9 (GSM US) Specifications
Codename: hiaeul
Vendor: HTC
Release date: 2015 November
Type: phone
Platform: Qualcomm MSM8952 Snapdragon 617
CPU: 4 x 1.5 GHz, 4 x 1.2 GHz octa-core Cortex A53
GPU: Adreno 405
RAM: 2/3GB
Weight: 143 g (5.04 oz)
Dimensions: 145.8 x 70.8 x 7.3 mm (5.74 x 2.79 x 0.29 in)
Screen size: 127 mm (5.0 in)
Resolution: 1080×1920
Screen density: 441 ppi
Screen type: AMOLED
Internal storage: 16/32GB
SD Card: up to 2TB
Bluetooth: 4.1
Wi-Fi: 802.11 a/b/g/n/ac (2.4 & 5 GHz)
Main camera: 13MP, flash: dual-LED
Secondary camera: 4MP
Power: 2150 mAh, Quick Charge 2.0
CM supported: 13, 14.1

How to Install CyanogenMod on the HTC One A9 (GSM US) (hiaeul)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

Note:

The One A9 (GSM US) can be unlocked officially via the HTC Dev unlock program. This unlock method may have certain restrictions, such as not being able to flash a kernel via recovery (no longer applicable to 2013+ released HTC devices) or no USB access to sdcard in recovery. Some devices, however, have no other method to install custom firmware.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to obtain your bootloader unlock token:
    fastboot oem get_identifier_token
  8. Visit the HTCDev Bootloader Unlock website and follow the instructions there to obtain your unlock key and unlock your bootloader. If your device does not appear in the drop-down list, select All Other Supported Models.
  9. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked.
  10. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  2. Download recovery — you can directly download a recovery image using the link below, or visit twrp.me to obtain the latest version of Team Win Recovery Project for your device.
    Recovery: Download
    md5: beaefd4f6baadfb375ad67001a78c6d8
  3. Connect the One A9 (GSM US) to the computer via USB.
  4. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  5. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  6. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  7. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  8. Once the flash completes successfully, reboot the device into recovery to verify the installation. Boot to recovery instructions: With the device powered down, hold the Volume Down and Power buttons until HBOOT appears, then release the buttons. Navigate using the volume keys and select RECOVERY using the Power key.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Installing CyanogenMod from recovery

  1. Make sure your computer has working adb.
  2. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  3. Place the CyanogenMod .zip package, as well as any optional .zip packages, on the root of /sdcard:
    • Using adb: adb push filename.zip /sdcard/
    Note: You can copy the .zip packages to your device using any method you are familiar with. The adb method is used here because it is universal across all devices and works in both Android and recovery mode. If you are in recovery mode, you may need to ensure /sdcard (sometimes called Internal Storage) is mounted by checking its status in the Mounts menu. If you have booted regularly, USB debugging must be enabled.
  4. If you are not already in recovery, boot to recovery mode now.
    • With the device powered down, hold the Volume Down and Power buttons until HBOOT appears, then release the buttons. Navigate using the volume keys and select RECOVERY using the Power key.
  5. In Team Win Recovery Project, select menu choices by tapping on the appropriately labelled button.
  6. Optional (Recommended): Select the Backup button to create a backup.
  7. Select Wipe and then Factory Reset.
  8. Select Install.
  9. Navigate to /sdcard and select the CyanogenMod .zip package.
  10. Follow the on-screen notices to install the package.
  11. Optional: Install any additional packages you wish using the same method (if you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it).
  12. Once installation has finished, return to the main menu and select Reboot, then System. The device will now boot into CyanogenMod.

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For HTC One A9 (GSM US) (hiaeul)

Introduction

These instructions will hopefully assist you to start with a stock One A9 (GSM US), unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A One A9 (GSM US)
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the One A9 (GSM US) (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b cm-13.0

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast hiaeul

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast hiaeul

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your One A9 (GSM US) is connected to your computer via the USB cable and that you are in the ~/android/system/device/htc/hiaeul directory (you can cd ~/android/system/device/htc/hiaeul if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/htc directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/htc directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch hiaeul

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make hiaeul should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/hiaeul/cm_hiaeul-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-13.0-20161224-UNOFFICIAL-hiaeul.zip, which is the CyanogenMod installation package.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  1. Connect the One A9 (GSM US) to the computer via USB.
  2. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  3. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  4. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  5. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  6. Once the flash completes successfully, reboot the device into recovery to verify the installation.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-13.0-20161224-UNOFFICIAL-hiaeul.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

Categories HTC

Nextbit Robin (ether)

CyanogenMod ROM Nextbit Robin (ether)

CyanogenMod ROM Nextbit Robin (ether)

Quick Info

Check out Nextbit Robin (“ether”) with newer LineageOS software

LineageOS

Download CyanogenMod

Download (nightly build)
CyanogenMod 14.1 (Android 7.1 (Nougat))

Special boot modes

  • Recovery: With the device powered down, hold the Volume Down and Power buttons.
  • Fastboot: With the device powered down, hold the Volume Up and Power buttons.

Source code

Device http://www.github.com/cyanogenmod/android_device_nextbit_ether
Kernel http://www.github.com/cyanogenmod/android_kernel_nextbit_msm8992
Robin Specifications
Codename: ether
Vendor: Nextbit
Release date: 2015 August
Type: phone
Platform: Qualcomm Snapdragon 808
CPU: 4 x 1.4 GHz & 2 x 1.8 GHz hexa-core Cortex A53 & A57
GPU: Adreno 418
RAM: 3GB
Weight: 150 g (5.3 oz)
Dimensions: 149 mm (5.9 in) (h)
72 mm (2.8 in) (w)
7 mm (0.28 in) (d)
Screen size: 132 mm (5.2 in)
Resolution: 1080×1920
Screen density: 424 ppi
Screen type: IPS LCD, Gorilla Glass 4
Internal storage: 32GB
Bluetooth: 4.0 LE
Wi-Fi: 802.11 a/b/g/n/ac
Main camera: 13MP, flash: dual-tone
Secondary camera: 5MP
Power: 2680 mAh
Sound: Dual front-facing
CM supported: 13, 14.1

How to Install CyanogenMod on the Nextbit Robin (ether)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to unlock the bootloader:
    fastboot oem unlock
  8. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked.
  9. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  2. Download recovery — you can directly download a recovery image using the link below, or visit twrp.me to obtain the latest version of Team Win Recovery Project for your device.
    Recovery: Download
    md5: b1d275d702de24358e08cc1e4f45d315
  3. Connect the Robin to the computer via USB.
  4. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  5. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  6. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  7. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  8. Once the flash completes successfully, reboot the device into recovery to verify the installation. Boot to recovery instructions: With the device powered down, hold the Volume Down and Power buttons.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Installing CyanogenMod from recovery

  1. Make sure your computer has working adb.
  2. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  3. Place the CyanogenMod .zip package, as well as any optional .zip packages, on the root of /sdcard:
    • Using adb: adb push filename.zip /sdcard/
    Note: You can copy the .zip packages to your device using any method you are familiar with. The adb method is used here because it is universal across all devices and works in both Android and recovery mode. If you are in recovery mode, you may need to ensure /sdcard (sometimes called Internal Storage) is mounted by checking its status in the Mounts menu. If you have booted regularly, USB debugging must be enabled.
  4. If you are not already in recovery, boot to recovery mode now.
    • With the device powered down, hold the Volume Down and Power buttons.
  5. In Team Win Recovery Project, select menu choices by tapping on the appropriately labelled button.
  6. Optional (Recommended): Select the Backup button to create a backup.
  7. Select Wipe and then Factory Reset.
  8. Select Install.
  9. Navigate to /sdcard and select the CyanogenMod .zip package.
  10. Follow the on-screen notices to install the package.
  11. Optional: Install any additional packages you wish using the same method (if you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it).
  12. Once installation has finished, return to the main menu and select Reboot, then System. The device will now boot into CyanogenMod.

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For Nextbit Robin (ether)

Introduction

These instructions will hopefully assist you to start with a stock Robin, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A Robin
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the Robin (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Unlocking your Robin

What does “unlocking” mean?

Note:

If you’ve already installed CyanogenMod or another ROM on your Robin, your device is already unlocked. Assuming you also have adb and fastboot installed on your computer, you can skip this whole section and proceed to the HOW TO BUILD section below.

The first step in putting any custom operating system on your Robin is to unlock the bootloader. A bootloader is the very first program that runs when you turn on your device. The bootloader initializes some hardware and then loads the kernel and ramdisk, and gets the boot process going. If the bootloader is in locked mode, it will ensure that only the stock operating system can run. Since you will be installing your own operating system, you need to turn this off. Luckily, Google and nextbit make it easy.

Note: A Warning About Unlocking

THE PROCESS OF UNLOCKING THE BOOTLOADER WILL ERASE ALL YOUR PERSONAL DATA FROM THE DEVICE.

Okay. I’m in. What do I need to do this?

To unlock your bootloader, you’ll first need a program on your computer called fastboot. One way to get fastboot is to download and install the Android SDK (Software Developer Kit) from Google. The SDK is used by app developers when they’re writing programs for Android, and who knows, you may want to write apps someday. But the SDK also contains two great tools that are useful even to non-developers. They are:

  • adb – Android Debug Bridge – this is a program that lets your computer “talk” to your Robin while the device is running. Among the many things you can do with adb– you can push files from your computer to the device or pull files from the device to your computer, you can get a running real-time log of Android activity (which is very useful for debugging or having others help you debug), you can create an interactive “shell” session (similar to Linux or OS X) to type commands to your device, and much more.

  • fastboot – fastboot works a little bit like adb, except it’s often used at a much earlier point in the boot process, even before Android or any operating system loads. You can put your Robin into a “fastboot” mode, whereby, if you are connected via USB cable, you can copy entire partitions from your computer (usually in the form of an image file, such as boot.img or recovery.img) over to the device, wiping over whatever happened to be there. Fastboot is able to do more than that, however. It’s also used to send special commands to the device to do things such as unlock your bootloader.

How do I do the actual unlocking?

So this should be a one time thing…

Install the Android SDK

To unlock your Robin, you will need fastboot installed. Go ahead and download the SDK, per the steps on Google’s web page. Then install it by following the specific instructions for your computer.

Note:

Google’s instructions may be out of date for 12.04. The Sun JDK isn’t available anymore as a dpkg AND they say Eclipse 3.6 isn’t available as a package. Well, 3.7.X is now available. Doing a “$ sudo apt-get install eclipse” will now install the proper Eclipse and JDK (OpenJDK 6).

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to unlock the bootloader:
    fastboot oem unlock
  8. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked.
  9. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Troubleshooting

If you have issues with fastboot or adb not being found, make sure that the Android SDK folder /platform-tools, which contains the adb and fastboot files, are in the path of execution for commands typed at the terminal. Usually typing something like 

# PATH=$PATH:/your/specific/path/to/android/sdk/platform-tools/

will work for that terminal session.

Note:

The above command requires a bash-like shell. If you’re running a linux distribution which uses a shell such as csh or tcsh, first run /bin/bash to start a bash shell. See http://www.cyberciti.biz/tips/how-do-i-find-out-what-shell-im-using.html or google for more help on that. You will need bash later as well, when using the “. build/envsetup.sh” command.

Note: Linux Mint users

If you have problems with adb (“file not found”) and you’re using 64-bit linux (I don’t know much about Mint, so maybe it’s all 64-bit?) try doing this to see if adb works better: 

$ sudo apt-get install ia32-libs

You’ll be using fastboot again to install a custom recovery.

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b cm-13.0

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast ether

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast ether

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your Robin is connected to your computer via the USB cable and that you are in the ~/android/system/device/nextbit/ether directory (you can cd ~/android/system/device/nextbit/ether if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/nextbit directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/nextbit directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch ether

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make ether should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/ether/cm_ether-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-13.0-20161224-UNOFFICIAL-ether.zip, which is the CyanogenMod installation package.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  1. Connect the Robin to the computer via USB.
  2. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  3. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  4. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  5. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  6. Once the flash completes successfully, reboot the device into recovery to verify the installation.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-13.0-20161224-UNOFFICIAL-ether.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

LG G2x (p999)

CyanogenMod ROM LG G2x (p999)

CyanogenMod ROM LG G2x (p999)

Quick Info

Download CyanogenMod

Download (nightly build)
CyanogenMod 7 (Android 2.3 (Gingerbread))

Note: Support Status

This device does not support the latest official release of CyanogenMod. This may be due to hardware limitations or simply because development is ongoing. The most recent version supported is based on the gingerbread branch of CyanogenMod.

Special boot modes

  • Recovery: Volume Down & Power

Source code

Device http://www.github.com/cyanogenmod/android_device_lge_p999
G2x Specifications
Codename: p999
Also known as: star
Vendor: LG
Manufacturer: lg
Carrier: T-Mobile (USA)
Type: phone
Platform: NVIDIA Tegra 2
CPU: 1 GHz dual-core NVIDIA Tegra 2
RAM: 512MB
Screen size: 102 mm (4.0 in)
Resolution: 800×480
Screen density: 233 ppi
Screen type: LCD
Internal storage: 8GB
SD Card: up to 32GB
Wi-Fi: 802.11 a/b/g/n
Main camera: 8MP
Secondary camera: 1.3MP
CM supported: 7
Latest CM version: gingerbread

How to Install CyanogenMod on the LG G2x (p999)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Installing CyanogenMod from recovery

  1. Make sure your computer has working adb.
  2. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  3. Boot to recovery mode, and connect the phone to your computer through USB.
    • Volume Down & Power
  4. In ClockworkMod Recovery, use the physical volume buttons to move up and down. On most devices, the power button is used to confirm a menu selection, but for some devices a physical home key acts as a selector. Some devices have touch enabled ClockworkMod Recovery, in which case you may be able to swipe to, or touch, menu selections.
  5. Optional (Recommended): Select backup and restore to create a backup.
  6. Select wipe data/factory reset.
  7. You have two options for transferring and installing the installation packages. The sideload method is more universal across devices, whereas the push and install method is more commonly used:
    • Sideload method: select install zip > install zip from sideload. Follow the on-screen notices to install the package. The installer does not necessarily display an “Install complete.” message. You can tell the install is complete if there were no fatal error messages and you have regained control over the menu.
    • Push and install method: Open a command prompt (or Terminal on Mac and Linux) and navigate to the directory holding the package(s) you would like to install. On the device, navigate to the mounts and storage menu. If you see /storage/sdcard0 or /sdcard as a mountable volume, go ahead and mount it. If you do not see one of these partitions, then instead mount the /data partition. Take note of which volume you mounted. Now, push the package(s) to your device (also, see tip below):
    – If you mounted /storage/sdcard0, then: adb push update.zip /storage/sdcard0/
    – If you mounted /sdcard or /data, then: adb push update.zip /sdcard/
    where update.zip should be replaced with the package filename. Go back to the main menu and select install zip. Choose to install from the same directory where you pushed the package(s). If you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it.
  8. Once installation has finished, return to the main menu and select reboot system now. The device will now boot into CyanogenMod.

Helpful Tip – SD card folders

CyanogenMod 10.1 and newer have multi-user support (introduced in Android 4.2). If your device has storage on the /data partition, then Android actually looks in /data/media/0/ for the first user’s /sdcard/ storage. ClockworkMod recovery symlinks /sdcard/ to /data/media/ though. So, if you are pushing files to internal storage in recovery and want them to be visible in Android, you should push them to /sdcard/0/ or /data/media/0/. Here’s the most frequent scenarios:

  1. If you’re coming from a ROM with Android 4.1 or older to CyanogenMod 10 or older: adb push update.zip /sdcard/
  2. If you’re coming from a ROM with Android 4.1 or older to CyanogenMod 10.1 or newer: adb shell "mkdir /sdcard/0/" followed by adb push update.zip /sdcard/0/
  3. If you’re coming from a ROM with Android 4.2 or newer to CyanogenMod 10.1 or newer: adb push update.zip /sdcard/0/

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For LG G2x (p999)

Introduction

These instructions will hopefully assist you to start with a stock G2x, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A G2x
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the G2x (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b gingerbread

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt Rom Manager

$ cd ~/android/system/vendor/cyanogen

then enter: 

$ ./get-rommanager

You won’t see any confirmation- just another prompt. But this should cause the Rom Manager apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type:

$ source build/envsetup.sh
$ lunch

You should see a list of devices, including something like cm_p999-userdebug. Select it by typing its number. It is possible that lunch does not display your device. In that case try 

$ lunch cm_p999-userdebug

or 

$ lunch full_p999-userdebug

If all goes well, you should see that p999-specific directories are downloaded automatically.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your G2x is connected to your computer via the USB cable and that you are in the ~/android/system/device/lge/p999 directory (you can cd ~/android/system/device/lge/p999 if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/lge directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/lge directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilt/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch p999

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make p999 should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/p999/cm_p999-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-7-20161224-UNOFFICIAL-p999.zip, which is the CyanogenMod installation package.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-7-20161224-UNOFFICIAL-p999.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

Categories LG

OnePlus X (onyx)

CyanogenMod ROM OnePlus X (onyx)

CyanogenMod ROM OnePlus X (onyx)

Quick Info

Check out OnePlus X (“onyx”) with newer LineageOS software

LineageOS

Download CyanogenMod

Download (nightly build)
CyanogenMod 14.1 (Android 7.1 (Nougat))

Download (nightly build)
CyanogenMod 14.1 (Android 7.1 (Nougat))

Special boot modes

  • Recovery: With the device powered down, hold the Volume Down and Power buttons.
  • Fastboot: With the device powered down, hold the Volume Up and Power buttons.

Source code

Device http://www.github.com/cyanogenmod/android_device_oneplus_onyx
Kernel http://www.github.com/cyanogenmod/android_kernel_oneplus_onyx
X Specifications
Codename: onyx
Vendor: OnePlus
Release date: 2015 November
Type: phone
Platform: Qualcomm Snapdragon 801
CPU: 2.3 GHz quad-core Krait 400
GPU: Adreno 330
RAM: 3GB
Weight: 138 g (4.86 oz)
Dimensions: 140 x 69 x 6.9 mm (5.51 x 2.72 x 0.27 in)
Screen size: 127 mm (5.0 in)
Resolution: 1080×1920
Screen density: ~441 ppi
Screen type: AMOLED
Internal storage: 16GB
SD Card: up to 128GB
Bluetooth: 4.0, A2DP
Wi-Fi: 802.11 b/g/n
Main camera: 13MP, flash: LED
Secondary camera: 8MP
Power: 2525 mAh LiPo
CM supported: 13, 14.1

How to Install CyanogenMod on the OnePlus X (onyx)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to unlock the bootloader:
    fastboot oem unlock
  8. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked.
  9. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  2. Download recovery — you can directly download a recovery image using the link below, or visit twrp.me to obtain the latest version of Team Win Recovery Project for your device.
    Recovery: Download
    md5: 0c74e1799c9814514b2d2397b44f1e41
  3. Connect the X to the computer via USB.
  4. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  5. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  6. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  7. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  8. Once the flash completes successfully, reboot the device into recovery to verify the installation. Boot to recovery instructions: With the device powered down, hold the Volume Down and Power buttons.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Installing CyanogenMod from recovery

  1. Make sure your computer has working adb.
  2. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  3. Place the CyanogenMod .zip package, as well as any optional .zip packages, on the root of /sdcard:
    • Using adb: adb push filename.zip /sdcard/
    Note: You can copy the .zip packages to your device using any method you are familiar with. The adb method is used here because it is universal across all devices and works in both Android and recovery mode. If you are in recovery mode, you may need to ensure /sdcard (sometimes called Internal Storage) is mounted by checking its status in the Mounts menu. If you have booted regularly, USB debugging must be enabled.
  4. If you are not already in recovery, boot to recovery mode now.
    • With the device powered down, hold the Volume Down and Power buttons.
  5. In Team Win Recovery Project, select menu choices by tapping on the appropriately labelled button.
  6. Optional (Recommended): Select the Backup button to create a backup.
  7. Select Wipe and then Factory Reset.
  8. Select Install.
  9. Navigate to /sdcard and select the CyanogenMod .zip package.
  10. Follow the on-screen notices to install the package.
  11. Optional: Install any additional packages you wish using the same method (if you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it).
  12. Once installation has finished, return to the main menu and select Reboot, then System. The device will now boot into CyanogenMod.

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For OnePlus X (onyx)

Introduction

These instructions will hopefully assist you to start with a stock X, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A X
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the X (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Unlocking your X

What does “unlocking” mean?

Note:

If you’ve already installed CyanogenMod or another ROM on your X, your device is already unlocked. Assuming you also have adb and fastboot installed on your computer, you can skip this whole section and proceed to the HOW TO BUILD section below.

The first step in putting any custom operating system on your X is to unlock the bootloader. A bootloader is the very first program that runs when you turn on your device. The bootloader initializes some hardware and then loads the kernel and ramdisk, and gets the boot process going. If the bootloader is in locked mode, it will ensure that only the stock operating system can run. Since you will be installing your own operating system, you need to turn this off. Luckily, Google and oneplus make it easy.

Note: A Warning About Unlocking

THE PROCESS OF UNLOCKING THE BOOTLOADER WILL ERASE ALL YOUR PERSONAL DATA FROM THE DEVICE.

Okay. I’m in. What do I need to do this?

To unlock your bootloader, you’ll first need a program on your computer called fastboot. One way to get fastboot is to download and install the Android SDK (Software Developer Kit) from Google. The SDK is used by app developers when they’re writing programs for Android, and who knows, you may want to write apps someday. But the SDK also contains two great tools that are useful even to non-developers. They are:

  • adb – Android Debug Bridge – this is a program that lets your computer “talk” to your X while the device is running. Among the many things you can do with adb– you can push files from your computer to the device or pull files from the device to your computer, you can get a running real-time log of Android activity (which is very useful for debugging or having others help you debug), you can create an interactive “shell” session (similar to Linux or OS X) to type commands to your device, and much more.

  • fastboot – fastboot works a little bit like adb, except it’s often used at a much earlier point in the boot process, even before Android or any operating system loads. You can put your X into a “fastboot” mode, whereby, if you are connected via USB cable, you can copy entire partitions from your computer (usually in the form of an image file, such as boot.img or recovery.img) over to the device, wiping over whatever happened to be there. Fastboot is able to do more than that, however. It’s also used to send special commands to the device to do things such as unlock your bootloader.

How do I do the actual unlocking?

So this should be a one time thing…

Install the Android SDK

To unlock your X, you will need fastboot installed. Go ahead and download the SDK, per the steps on Google’s web page. Then install it by following the specific instructions for your computer.

Note:

Google’s instructions may be out of date for 12.04. The Sun JDK isn’t available anymore as a dpkg AND they say Eclipse 3.6 isn’t available as a package. Well, 3.7.X is now available. Doing a “$ sudo apt-get install eclipse” will now install the proper Eclipse and JDK (OpenJDK 6).

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to unlock the bootloader:
    fastboot oem unlock
  8. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked.
  9. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Troubleshooting

If you have issues with fastboot or adb not being found, make sure that the Android SDK folder /platform-tools, which contains the adb and fastboot files, are in the path of execution for commands typed at the terminal. Usually typing something like 

# PATH=$PATH:/your/specific/path/to/android/sdk/platform-tools/

will work for that terminal session.

Note:

The above command requires a bash-like shell. If you’re running a linux distribution which uses a shell such as csh or tcsh, first run /bin/bash to start a bash shell. See http://www.cyberciti.biz/tips/how-do-i-find-out-what-shell-im-using.html or google for more help on that. You will need bash later as well, when using the “. build/envsetup.sh” command.

Note: Linux Mint users

If you have problems with adb (“file not found”) and you’re using 64-bit linux (I don’t know much about Mint, so maybe it’s all 64-bit?) try doing this to see if adb works better: 

$ sudo apt-get install ia32-libs

You’ll be using fastboot again to install a custom recovery.

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b cm-13.0

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast onyx

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast onyx

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your X is connected to your computer via the USB cable and that you are in the ~/android/system/device/oneplus/onyx directory (you can cd ~/android/system/device/oneplus/onyx if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/oneplus directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/oneplus directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch onyx

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make onyx should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/onyx/cm_onyx-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-13.0-20161224-UNOFFICIAL-onyx.zip, which is the CyanogenMod installation package.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  1. Connect the X to the computer via USB.
  2. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  3. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  4. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  5. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  6. Once the flash completes successfully, reboot the device into recovery to verify the installation.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-13.0-20161224-UNOFFICIAL-onyx.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

LG MyTouch Q (c800)

CyanogenMod ROM LG MyTouch Q (c800)

CyanogenMod ROM LG MyTouch Q (c800)

Quick Info

Download CyanogenMod

Download (nightly build)
CyanogenMod 9 (Android 4.0.4 (Ice Cream Sandwich))

Note: Support Status

This device does not support the latest official release of CyanogenMod. This may be due to hardware limitations or simply because development is ongoing. The most recent version supported is based on the ics branch of CyanogenMod.

Source code

Device http://www.github.com/cyanogenmod/android_device_lge_c800
Kernel http://www.github.com/cyanogenmod/lge-kernel-msm7x30
MyTouch Q Specifications
Codename: c800
Vendor: LG
Manufacturer: LG
Type: phone (slider)
GSM freq: GSM 850 / 900 / 1800 / 1900
HSDPA 1700 / 2100
Platform: Qualcomm MSM8255
CPU: 1 GHz single-core Scorpion Snapdragon S2
GPU: Adreno 205
RAM: 512MB
Weight: 160 g (5.64 oz)
Dimensions: 121 x 64 x 13 mm (4.76 x 2.52 x 0.51 in)
Screen size: 89 mm (3.5 in)
Resolution: 320×480
Screen density: 165 ppi
Internal storage: 2GB
SD Card: up to 32GB
Bluetooth: 3.0
Wi-Fi: 802.11 b/g/n
Main camera: 5MP
Power: Li-Ion 1500 mAh battery
Peripherals: Accelerometer, proximity
CM supported: 9
Latest CM version: ics

How to Install CyanogenMod on the LG MyTouch Q (c800)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  2. Download recovery — you can directly download a recovery image using the link below, or visit twrp.me to obtain the latest version of Team Win Recovery Project for your device.
    Recovery: Download
    md5: b8d15a0ee9486f0a9662dd5747c50c43
  3. Connect the MyTouch Q to the computer via USB.
  4. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  5. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  6. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  7. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  8. Once the flash completes successfully, reboot the device into recovery to verify the installation.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Installing CyanogenMod from recovery

  1. Make sure your computer has working adb.
  2. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  3. Boot to recovery mode, and connect the phone to your computer through USB.
  1. In ClockworkMod Recovery, use the physical volume buttons to move up and down. On most devices, the power button is used to confirm a menu selection, but for some devices a physical home key acts as a selector. Some devices have touch enabled ClockworkMod Recovery, in which case you may be able to swipe to, or touch, menu selections.
  2. Optional (Recommended): Select backup and restore to create a backup.
  3. Select wipe data/factory reset.
  4. You have two options for transferring and installing the installation packages. The sideload method is more universal across devices, whereas the push and install method is more commonly used:
    • Sideload method: select install zip > install zip from sideload. Follow the on-screen notices to install the package. The installer does not necessarily display an “Install complete.” message. You can tell the install is complete if there were no fatal error messages and you have regained control over the menu.
    • Push and install method: Open a command prompt (or Terminal on Mac and Linux) and navigate to the directory holding the package(s) you would like to install. On the device, navigate to the mounts and storage menu. If you see /storage/sdcard0 or /sdcard as a mountable volume, go ahead and mount it. If you do not see one of these partitions, then instead mount the /data partition. Take note of which volume you mounted. Now, push the package(s) to your device (also, see tip below):
    – If you mounted /storage/sdcard0, then: adb push update.zip /storage/sdcard0/
    – If you mounted /sdcard or /data, then: adb push update.zip /sdcard/
    where update.zip should be replaced with the package filename. Go back to the main menu and select install zip. Choose to install from the same directory where you pushed the package(s). If you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it.
  5. Once installation has finished, return to the main menu and select reboot system now. The device will now boot into CyanogenMod.

Helpful Tip – SD card folders

CyanogenMod 10.1 and newer have multi-user support (introduced in Android 4.2). If your device has storage on the /data partition, then Android actually looks in /data/media/0/ for the first user’s /sdcard/ storage. ClockworkMod recovery symlinks /sdcard/ to /data/media/ though. So, if you are pushing files to internal storage in recovery and want them to be visible in Android, you should push them to /sdcard/0/ or /data/media/0/. Here’s the most frequent scenarios:

  1. If you’re coming from a ROM with Android 4.1 or older to CyanogenMod 10 or older: adb push update.zip /sdcard/
  2. If you’re coming from a ROM with Android 4.1 or older to CyanogenMod 10.1 or newer: adb shell "mkdir /sdcard/0/" followed by adb push update.zip /sdcard/0/
  3. If you’re coming from a ROM with Android 4.2 or newer to CyanogenMod 10.1 or newer: adb push update.zip /sdcard/0/

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For LG MyTouch Q (c800)

Introduction

These instructions will hopefully assist you to start with a stock MyTouch Q, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A MyTouch Q
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the MyTouch Q (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b ics

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast c800

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast c800

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your MyTouch Q is connected to your computer via the USB cable and that you are in the ~/android/system/device/lge/c800 directory (you can cd ~/android/system/device/lge/c800 if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/lge directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/lge directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch c800

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make c800 should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/c800/cm_c800-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-9-20161224-UNOFFICIAL-c800.zip, which is the CyanogenMod installation package.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  1. Connect the MyTouch Q to the computer via USB.
  2. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  3. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  4. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  5. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  6. Once the flash completes successfully, reboot the device into recovery to verify the installation.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-9-20161224-UNOFFICIAL-c800.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

Categories LG

HTC Desire 816 Dual SIM (a5dwg)

CyanogenMod ROM HTC Desire 816 Dual SIM (a5dwg)

CyanogenMod ROM HTC Desire 816 Dual SIM (a5dwg)

Quick Info

Download CyanogenMod

Download (nightly build)
CyanogenMod 13.0 (Android 6.0/6.0.1 (Marshmallow))

Special boot modes

  • Recovery: With the device powered down, hold the Volume Down and Power buttons until HBOOT appears, then release the buttons. Navigate using the volume keys and select RECOVERY using the Power key.
  • Bootloader: With the device powered down, hold the Volume Down and Power buttons until HBOOT appears, then release the buttons.
  • Fastboot: With the device powered down, hold the Volume Down and Power buttons until HBOOT appears, then release the buttons. Navigate using the volume keys and select FASTBOOT using the Power key.

Source code

Device http://www.github.com/cyanogenmod/android_device_htc_a5dwg
Kernel http://www.github.com/cyanogenmod/android_kernel_htc_msm8974
Desire 816 Dual SIM Specifications
Codename: a5dwg
Vendor: HTC
Manufacturer: HTC
Release date: 2014 April
Type: phone
GSM freq: GSM 850 / 900 / 1800 / 1900

HSDPA 850 / 900 / 2100

Platform: Qualcomm MSM8226 Snapdragon 400
CPU: 1.6 GHz quad-core Cortex A7
GPU: Adreno 305
RAM: 1.5GB
Weight: 165 g (5.82 oz)
Dimensions: 156.6 mm (6.17 in) x 78.7 mm (3.10 in) x 7.9 mm (0.31 in)
Screen size: 139.7 mm (5.5 in)
Resolution: 1280×720 pixels
Screen density: ~267 ppi
Screen type: Super LCD2 capacitive touchscreen, 16M colors
Internal storage: 8GB
SD Card: up to 128GB
Bluetooth: v4.0 with A2DP, LE
Wi-Fi: Wi-Fi 802.11 b/g/n, DLNA, Wi-Fi hotspot
Main camera: 13MP, flash: LED
Secondary camera: 5MP
Power: 2600 mAh
Peripherals: Accelerometer, proximity, compass
CM supported: 13

How to Install CyanogenMod on the HTC Desire 816 Dual SIM (a5dwg)

Note: DISCLAIMER

Modifying or replacing your device’s software may void your device’s warranty, lead to data loss, hair loss, financial loss, privacy loss, security breaches, or other damage, and therefore must be done entirely at your own risk. No one affiliated with the CyanogenMod project is responsible for your actions. Good luck.

Unlocking the bootloader

WARNING:

Unlocking the bootloader will automatically wipe all device data.

Note:

The Desire 816 Dual SIM can be unlocked officially via the HTC Dev unlock program. This unlock method may have certain restrictions, such as not being able to flash a kernel via recovery (no longer applicable to 2013+ released HTC devices) or no USB access to sdcard in recovery. Some devices, however, have no other method to install custom firmware.

  1. Make sure your computer has working fastboot and adb.
  2. Enable USB debugging on the device.
  3. Enable OEM unlock in the Developer options settings on the device. (Note: Not all devices have this setting, so continue with next step if yours does not.)
  4. Connect the device to the computer through USB.
  5. From a terminal on a computer, type the following to boot the device into fastboot mode:
    adb reboot bootloader
  6. Once the device is in fastboot mode, verify your PC sees the device by typing fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissions fastboot”, try running fastboot as root.
  7. From the same terminal, type the following command to obtain your bootloader unlock token:
    fastboot oem get_identifier_token
  8. Visit the HTCDev Bootloader Unlock website and follow the instructions there to obtain your unlock key and unlock your bootloader. If your device does not appear in the drop-down list, select All Other Supported Models.
  9. If the device doesn’t automatically reboot, reboot it from the menu. It should now be unlocked.
  10. Since the device resets completely, you will need to re-enable USB debugging on the device to continue.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  2. Download recovery — you can directly download a recovery image using the link below, or visit twrp.me to obtain the latest version of Team Win Recovery Project for your device.
    Recovery: Download
    md5: 98c273cb3f919d5d99de9c6b071e1581
  3. Connect the Desire 816 Dual SIM to the computer via USB.
  4. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  5. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  6. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  7. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  8. Once the flash completes successfully, reboot the device into recovery to verify the installation. Boot to recovery instructions: With the device powered down, hold the Volume Down and Power buttons until HBOOT appears, then release the buttons. Navigate using the volume keys and select RECOVERY using the Power key.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Installing CyanogenMod from recovery

  1. Make sure your computer has working adb.
  2. Download the CyanogenMod build package for your device that you’d like to install to your computer.
    Optional: Download 3rd party applications packages, like Google Apps which are necessary to download apps from Google Play.
  3. Place the CyanogenMod .zip package, as well as any optional .zip packages, on the root of /sdcard:
    • Using adb: adb push filename.zip /sdcard/
    Note: You can copy the .zip packages to your device using any method you are familiar with. The adb method is used here because it is universal across all devices and works in both Android and recovery mode. If you are in recovery mode, you may need to ensure /sdcard (sometimes called Internal Storage) is mounted by checking its status in the Mounts menu. If you have booted regularly, USB debugging must be enabled.
  4. If you are not already in recovery, boot to recovery mode now.
    • With the device powered down, hold the Volume Down and Power buttons until HBOOT appears, then release the buttons. Navigate using the volume keys and select RECOVERY using the Power key.
  5. In Team Win Recovery Project, select menu choices by tapping on the appropriately labelled button.
  6. Optional (Recommended): Select the Backup button to create a backup.
  7. Select Wipe and then Factory Reset.
  8. Select Install.
  9. Navigate to /sdcard and select the CyanogenMod .zip package.
  10. Follow the on-screen notices to install the package.
  11. Optional: Install any additional packages you wish using the same method (if you are installing multiple packages, install CyanogenMod first and then install any subsequent packages on top of it).
  12. Once installation has finished, return to the main menu and select Reboot, then System. The device will now boot into CyanogenMod.

Helpful Tip

See something wrong on this page? Click here: Report a Site Problem.

How To Build CyanogenMod For HTC Desire 816 Dual SIM (a5dwg)

Introduction

These instructions will hopefully assist you to start with a stock Desire 816 Dual SIM, unlock the bootloader (if necessary), and then download the required tools as well as the very latest source code for CyanogenMod (based on Google’s Android operating system). Using these, you can build both CyanogenMod and CyanogenMod Recovery image from source code, and then install them both to your device.

It is difficult to say how much experience is necessary to follow these instructions. While this guide is certainly not for the very very very uninitiated, these steps shouldn’t require a PhD in software development either. Some readers will have no difficulty and breeze through the steps easily. Others may struggle over the most basic operation. Because people’s experiences, backgrounds, and intuitions differ, it may be a good idea to read through just to ascertain whether you feel comfortable or are getting over your head.

Remember, you assume all risk of trying this, but you will reap the rewards! It’s pretty satisfying to boot into a fresh operating system you baked at home :) And once you’re an Android-building ninja, there will be no more need to wait for “nightly” builds from anyone. You will have at your fingertips the skills to build a full operating system from code to a running device, whenever you want. Where you go from there– maybe you’ll add a feature, fix a bug, add a translation, or use what you’ve learned to build a new app or port to a new device– or maybe you’ll never build again– it’s all really up to you.

What you’ll need

  • A Desire 816 Dual SIM
  • A relatively recent computer (Linux, OS X, or Windows) with a reasonable amount of RAM and about 100 GB of free storage (more if you enable ccache or build for multiple devices). The less RAM you have, the longer the build will take (aim for 8 GB or more). Using SSDs results in considerably faster build times than traditional hard drives.
  • A USB cable compatible with the Desire 816 Dual SIM (typically micro USB, but older devices may use mini USB or have a proprietary cable)
  • A decent internet connection & reliable electricity :)
  • Some familiarity with basic Android operation and terminology. It would help if you’ve installed custom roms on other devices and are familiar with recovery. It may also be useful to know some basic command line concepts such as cd for “change directory”, the concept of directory hierarchies, that in Linux they are separated by /, etc.

If you are not accustomed to using Linux– this is an excellent chance to learn. It’s free– just download and run a virtual machine (VM) such as Virtualbox, then install a Linux distribution such as Ubuntu (AOSP vets Ubuntu as well). Any recent 64-bit version should work great, but the latest is recommended.

Note:

You want to use a 64-bit version of Linux. A 32-bit Linux environment will only work if you are building CyanogenMod 6 and older. For CyanogenMod 10.1, if you encounter issues with 64bit host binaries, you can set BUILD_HOST_32bit=1 in your environment. This is generally not needed, though, especially with CyanogenMod 10.2 and newer.

Using a VM allows Linux to run as a guest inside your host computer– a computer in a computer, if you will. If you hate Linux for whatever reason, you can always just uninstall and delete the whole thing. (There are plenty of places to find instructions for setting up Virtualbox with Ubuntu, so I’ll leave it to you to do that.)

So let’s begin!

Build CyanogenMod and CyanogenMod Recovery

Prepare the Build Environment

Note:

You only need to do these steps the first time you build. If you previously prepared your build environment and have downloaded the CyanogenMod source code for another device, skip to Prepare the device-specific code.

Install the SDK

If you have not previously installed adb and fastboot, install the Android SDK. “SDK” stands for Software Developer Kit, and it includes useful tools that you can use to flash software, look at the system logs in real time, grab screenshots, and more– all from your computer.

Helpful Tip

While the SDK contains lots of different things– the two tools you are most interested in for building Android are adb and fastboot, located in the /platform-tools directory.

Install the Build Packages

Several “build packages” are needed to build CyanogenMod. You can install these using the package manager of your choice.

Helpful Tip

A package manager in Linux is a system used to install or remove software (usually originating from the Internet) on your computer. With Ubuntu, you can use the Ubuntu Software Center. Even better, you may also use the apt-get install command directly in the Terminal. (Learn more about the apt packaging tool system from Wikipedia.)

For both 32-bit & 64-bit systems, you’ll need: 

bc bison build-essential curl flex git gnupg gperf libesd0-dev liblz4-tool libncurses5-dev libsdl1.2-dev libwxgtk2.8-dev libxml2 libxml2-utils lzop maven openjdk-7-jdk pngcrush schedtool squashfs-tools xsltproc zip zlib1g-dev

In addition to the above, for 64-bit systems, get these: 

g++-multilib gcc-multilib lib32ncurses5-dev lib32readline-gplv2-dev lib32z1-dev

For Ubuntu 15.10 (wily) and newer, substitute:

  • lib32readline-gplv2-dev → lib32readline6-dev

For Ubuntu 16.04 (xenial) and newer, substitute (additionally see java notes below):

  • libwxgtk2.8-dev → libwxgtk3.0-dev
  • openjdk-7-jdk → openjdk-8-jdk

Java versions: Different versions of CyanogenMod require different versions of the JDK (Java Development Kit):

  • CyanogenMod 7 – 9: Sun/Oracle Java SE 1.6
  • CyanogenMod 10.1: Sun/Oracle Java SE 1.6 or 1.7
  • CyanogenMod 10.2 – 11.0: Sun/Oracle Java SE 1.6 or 1.7 (OpenJDK 1.7 works fine, but the build system will display a warning)
  • CyanogenMod 12.0 – 13.0: OpenJDK 1.7 (see note about OpenJDK 1.8 below)
  • CyanogenMod 14.1: OpenJDK 1.8

Ubuntu 16.04 (Xenial Xerus) or newer and OpenJDK: Since OpenJDK 1.7 was removed from the official Ubuntu repositories, you have a couple options:

  1. Obtain OpenJDK 1.7 from the openjdk-r PPA
  2. Enable experimental OpenJDK 1.8 support in CyanogenMod 13.0 (not available in earlier version). To enable OpenJDK 1.8 support, add this line to your $HOME/.bashrc file: export EXPERIMENTAL_USE_JAVA8=true.

Also see http://source.android.com/source/initializing.html which lists needed packages.

Create the directories

You will need to set up some directories in your build environment.

To create them: 

$ mkdir -p ~/bin
$ mkdir -p ~/android/system

Install the repo command

Enter the following to download the “repo” binary and make it executable (runnable): 

$ curl https://storage.googleapis.com/git-repo-downloads/repo > ~/bin/repo
$ chmod a+x ~/bin/repo

Put the ~/bin directory in your path of execution

In recent versions of Ubuntu, ~/bin should already be in your PATH. You can check this by opening ~/.profile with a text editor and verifying the following code exists (add it if it is missing): 

# set PATH so it includes user's private bin if it exists
if [ -d "$HOME/bin" ] ; then
    PATH="$HOME/bin:$PATH"
fi

Initialize the CyanogenMod source repository

Enter the following to initialize the repository:

Note: Make sure the cm branch entered here is the one you wish to build and is supported on your device.
$ cd ~/android/system/
$ repo init -u https://github.com/CyanogenMod/android.git -b cm-13.0

Download the source code

To start the download of all the source code to your computer: 

$ repo sync

The CM manifests include a sensible default configuration for repo, which we strongly suggest you use (i.e. don’t add any options to sync). For reference, our default values are -j 4 and -c. The -j 4 part means that there will be four simultaneous threads/connections. If you experience problems syncing, you can lower this to -j 3 or -j 2. -c will ask repo to pull in only the current branch, instead of the entire CM history.

Prepare to wait a long time while the source code downloads.

Helpful Tip

The repo sync command is used to update the latest source code from CyanogenMod and Google. Remember it, as you can do it every few days to keep your code base fresh and up-to-date.

Get prebuilt apps (CM11 and below)

Next, 

$ cd ~/android/system/vendor/cm

then enter: 

$ ./get-prebuilts

You won’t see any confirmation- just another prompt. But this should cause some prebuilt apps to be loaded and installed into the source code. Once completed, this does not need to be done again.

Prepare the device-specific code

Helpful Tip – Errors during breakfast

Different maintainers setup their device inheritance rules differently. Some require a vendor directory to be populated before breakfast will even succeed. If you receive an error here about vendor makefiles, then jump down to the next section Extract proprietary blobs. The first portion of breakfast should have succeeded at pulling in the device tree and the extract blobs script should be available. After completing that section, you can rerun breakfast a5dwg

After the source downloads, ensure you are in the root of the source code (cd ~/android/system), then type: 

$ source build/envsetup.sh
$ breakfast a5dwg

This will download the device specific configuration and kernel source for your device. An alternative to using the breakfast command is to build your own local manifest. To do this, you will need to locate your device on CyanogenMod’s GitHub and list all of the repositories defined in cm.dependencies in your local manifest.

Helpful Tip

If you want to know more about what source build/envsetup.sh does or simply want to know more about the breakfast, brunch and lunch commands, you can head over to the Envsetup help page.

Helpful Tip

Instead of typing cd ~/android/system every time you want to return back to the root of the source code, here’s a short command that will do it for you: croot. To use this command, you must first run source build/envsetup.sh from ~/android/system.

Extract proprietary blobs

Now ensure that your Desire 816 Dual SIM is connected to your computer via the USB cable and that you are in the ~/android/system/device/htc/a5dwg directory (you can cd ~/android/system/device/htc/a5dwg if necessary). Then run the extract-files.sh script: 

$ ./extract-files.sh

You should see the proprietary files (aka “blobs”) get pulled from the device and moved to the ~/android/system/vendor/htc directory. If you see errors about adb being unable to pull the files, adb may not be in the path of execution. If this is the case, see the adb page for suggestions for dealing with “command not found” errors.

Note:

Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly.

Note:

It’s important that these proprietary files are extracted to the ~/android/system/vendor/htc directory by using the extract-files.sh script. Makefiles are generated at the same time to make sure the blobs are eventually copied to the device. Without these blobs, CyanogenMod may build without error, but you’ll be missing important functionality, such as graphics libraries that enable you to see anything!

Turn on caching to speed up build

You can speed up subsequent builds by adding 

export USE_CCACHE=1

to your ~/.bashrc file (what’s a .bashrc file?). Then, specify the amount of disk space to dedicate to ccache by typing this from the top of your Android tree: 

prebuilts/misc/linux-x86/ccache/ccache -M 50G

where 50G corresponds to 50GB of cache. This only needs to be run once and the setting will be remembered. Anywhere in the range of 25GB to 100GB will result in very noticeably increased build speeds (for instance, a typical 1hr build time can be reduced to 20min). If you’re only building for one device, 25GB-50GB is fine. If you plan to build for several devices that do not share the same kernel source, aim for 75GB-100GB. This space will be permanently occupied on your drive, so take this into consideration. See more information about ccache on Google’s android build environment initialization page.

Helpful Tip

If you are a very active developer, working on many other projects than just Android, you might prefer to keep your Android ccache independent (because it’s huge and can slow down the efficiency of ccache in your other projects). Beginning with CyanogenMod 12.1, you can specify environment variables for the location and size of CyanogenMod’s ccache. Some syntax examples: export ANDROID_CCACHE_DIR="$HOME/android/.ccache" and export ANDROID_CCACHE_SIZE="50G".

Start the build

Time to start building! So now type: 

$ croot
$ brunch a5dwg

The build should begin.

Helpful Tip

If the build doesn’t start, try lunch and choose your device from the menu. If that doesn’t work, try breakfast and choose from the menu. The command make a5dwg should then work.

Helpful Tip

A second, bonus tip! If you get a command not found error for croot, brunch, or lunch, be sure you’ve done the source build/envsetup.sh command in this Terminal session from the ~/android/system directory.

Helpful Tip

A third tip! If the build to fails while downloading Gello, you’ll need to import a missing certificate into Maven’s truststore. Detailed instructions on how to do that can be found here

If the build breaks…

  • If you experience this not-enough-memory-related error…
ERROR: signapk.jar failed: return code 1make: *** [out/target/product/a5dwg/cm_a5dwg-ota-eng.root.zip] Error 1

…you may want to make the following change to ~/android/system/build/tools/releasetools/common.py:

Search for instances of -Xmx2048m (it should appear either under OPTIONS.java_args or near usage of signapk.jar), and replace it with -Xmx1024m or -Xmx512m.

Then start the build again (with brunch).

  • If you see a message about things suddenly being “killed” for no reason, your (virtual) machine may have run out of memory or storage space. Assign it more resources and try again.

Install the build

Assuming the build completed without error (it will be obvious when it finishes), type: 

$ cd $OUT

in the same terminal window that you did the build. Here you’ll find all the files that were created. The stuff that will go in /system is in a folder called system. The stuff that will become your ramdisk is in a folder called root. And your kernel is called… kernel.

But that’s all just background info. The two files we are interested in are (1) recovery.img, which contains CyanogenMod Recovery, and (2) cm-13.0-20161224-UNOFFICIAL-a5dwg.zip, which is the CyanogenMod installation package.

Installing a custom recovery using fastboot

See All About Recovery Images for more information about custom recoveries and their capabilities.

  1. Make sure your computer has working fastboot and adb.
  1. Connect the Desire 816 Dual SIM to the computer via USB.
  2. Make sure the fastboot binary is in your PATH or that you place the recovery image in the same directory as fastboot.
  3. Open a terminal on your PC and reboot the device into fastboot mode by typing
    adb reboot bootloader
    or by using the hardware key combination for your device while it is powered off.
  4. Once the device is in fastboot mode, verify your PC sees the device by typing
    fastboot devices
    • If you don’t see your device serial number, and instead see “<waiting for device>”, fastboot is not configured properly on your machine. See fastboot documentation for more info.
    • If you see “no permissionsfastboot”, make sure your UDEV rules are setup correctly.
  5. Flash recovery onto your device by entering the following command:
    fastboot flash recovery your_recovery_image.img
    where the latter part is the filename of the recovery image.
  6. Once the flash completes successfully, reboot the device into recovery to verify the installation.
    • Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one.

Install CyanogenMod

Back to the $OUT directory on your computer– you should see a file that looks something like: 

cm-13.0-20161224-UNOFFICIAL-a5dwg.zip

Note:

The above file name may vary depending on the version of CM you are building. Your build may not include a version number or may identify itself as a “KANG” rather than UNOFFICIAL version. Regardless, the file name will end in .zip and should be titled similarly to official builds.

Now you can flash the cm...zip file above as usual via recovery mode. Before doing so, now is a good time to make a backup of whatever installation is currently running on the device in case something goes wrong with the flash attempt. While CyanogenMod Recovery doesn’t have a backup feature, there are other custom recoveries available that do. You can also use something like Titanium Backup (root required) as an alternative.

Success! So….what’s next?

You’ve done it! Welcome to the elite club of self-builders. You’ve built your operating system from scratch, from the ground up. You are the master/mistress of your domain… and hopefully you’ve learned a bit on the way and had some fun too.

Now that you’ve succeeded in building CyanogenMod for your device, here are some suggestions on what to do next.

Also, be sure to take a glance at the Dev Center on this wiki for all kinds of more detailed information about developer topics ranging from collecting logs, understanding what’s in the source code directories, submitting your own contributions, porting CyanogenMod to new devices, and a lot more.

Congrats again!

Content of this page is based on informations from wiki.cyanogenmod.org, under CC BY-SA 3.0 licence.

Categories HTC